Китайские Карьерные самосвалы

Frame
Fabricated full box section frame with integral front bumper and closed loop crossmember. Crossmember and rear torque tube and tail seat connentions with frame rails are high strength alloy castings.

Engine
Model:Cummins M11-C350
Type: 4 Cycle,Turbocharged/Aftercooled,Direct injection
Gross Power@2100rpm:261KW(350hp)
Net Power@2100rpm:238KW(319hp)
Gross Power rated to SAE J1995 Jun 90.Engine emission meets USA EPA/CARB Moh 40 CFR 89 and proposed EU non-road mobile machinery directive.
Maximum Torque @ 1300rpm:1559 Nm(1150ibf ft)
Cylinders/Configuration: 6 in line
Bore X Stroke:125 X 147mm (4.92 X 5.79 in )
Displacement: 10.8L ( 661 in 3)
24 volt negative ground electrical system with master disconnect switch; two 12v, 165Ah batteries; 65A altermator with integral voltage regulator; one electric starter .Neutral start lock-up protection

Transmission

ZF 6HP602 Automatic electronic controlled with integral lock-up clutch single converter,hydraulic reducer,planetary gearbox,complete oil cooter and output devices. Six speeds forward and one reverse. Braking force of hydraulic reducer controlled by joystick.Under excellent working condition the clutch lock up aytomatically after start .Electronic_hydraulic shift ensure that the soft shifting is at optimal point and unlock in short time.

Standard differential speed :

	Forward						Reverse
	1st	2nd	3rd	4th	5th	6th
Ratioos	5.6	3.48	2.01	1.42	1.0	0.83	4.84
Speed(km/h)	10.8	12.6	21.9	30.9	43.9	52.9	9.0

Drive Axle

TEREX heavy duty axle with full floating axle shafts, single reduction sprial bevel gear differential, and planetary reduction at each wheel.

Standard:
Ratios: Differential 3.13:1
Planetary 4.59:1
Total Reduction 14.37:1

Suspension

Front :TEREX manufactured kin pin strut type independent front wheel suspension by self-contained ,variable rate, nitrogen/oil cylinder. Rear :TEREX variable rate nitrogen/oil cylinder with A-frame linkage and lateral stabilizer bar.
Maximum Strut Stroke:Front: 225mm ( 9.0in )
Rear: 160mm ( 6.3in )
Maximum Rear Oscillation:±8°

Tyres

Standard:front & rear 18.00-25(32PR)E-3: 13in
Note:Under certain job conditon the t-km/h(ton-mile/h)capacity of standard or optional tyres may be exceeded .We recommend that tyre manufacturers be consulted for optimum type selection.

Brakes

SERVICE:dualshoe,internal expanding,mechanically actuated by air pressure.Independednt front and rear circle systems actuated by single treadle valve with auxiliary manual control.Operator controlled dry/wet road valve reduces front brake pressure 50% for improved control in slippery conditions
Front Linings:Diameter x width:508x 152 mm (20x 6 in )
Lining area-front axle: 3459 cm 2( 536 in 2)
Rear Linings: Diameter x width::508x 190 mm (20x 7.5 in )
Lining area-rear axle: 4323 cm 2( 670 in 2)
Total Lining Area: 7782 cm 2( 1206 in 2)

Emergency:Warning light in cab indicates when air pressure drops below 550Kpa(80ibf/in2).Front and rear brakes automatically actuates if system air pressure falls to 310Kpa(45ibf/in2)
Air Compressor Capacity: 533L /min( 18.7ft3 /min)
Total Satety Brake Air Reservoir Capacity: 81L ( 4950in 3)
PARKING:Serbice brakes act as parking brakes and mechanical lock-up when applied by manual control valve on instrument panel. Brake conform to ISO3450,SAE J 1473 OCT90.

Steering

Independent hydrostatic steering with closed-center steering valve,accumulator and pressure compensating piston pump.Accumulator provides uniform steering regardless of engine speed .In the event of loss of engine power it provide emergency steering of approximately two lock-to-lock turns.
A low pressure warning light indicates ahould the system pressure fall below 8274Kpa(1200ibf/in2)
Maximum Steering Angle:4 2 ·
Steering conforms to ISO5010,SAE J53

Hoist

Two body hoists mounted inside the frame rails.Hoist are two –stage with power down in the second stage.The body hydraulic system is independent of the steering hydraulic system.
System Pressure:13.8Mpa(2000ibf/in2)
Boday Hydraulic pump Flow Rate @ 2100rpm 210L /min(55.5US gal/min)Body Raise Time:14 seconds
Lower Time :9 seconds

Body

Longitudinal “V” shape floor with integral tranvers box –section stiffeners.The strengthened and anti-impacting large –section crossed side plates.The body is exhaust heated and rests on removable resilient inpact absorption pads.
The floor plate is high hardness abrasion resistant steel of high yield strength.Cabguard ROPS SAE J 104C Feb 86 and ISO3471.
Normal body parameters
Thickness:
Floor: 16mm ( 0.63in )
Side: 8mm ( 0.31 in )
Front: 10mm ( 0.39in )
Capacity:
Struck(SAE): 16.1m3 ( 21.2yd3 )
Heaped3:1 : 19.5m3 ( 25.1yd3 )
Heaped(SAE)2:1 : 21.1m3 ( 27.7yd3 )

Standard Equipment
CAB Low Brake Pressure
Acoustic Lining Transmission Filter Restriction
Door Locks Hydraulic Filter Restriction
Floor Mat Steering Filter Restriction
ROPS Body Cabguard ISO 3471/ Charge indicator
SAE J 1040 Warning Light Test
Heater and Defroster Engine Oil Pressure Low
Interior Light General:
Illuminated Instrucment Panel Accumulator Safety Steering
Seat ,Spring suspension ,adjustable Air cleaner ,two stage with safety
Seat ,Passenger element
Seat Belts SAE J386 Radiator ,replaceable tube core
Steering Column-adjustable Body Down Signal
Sun VisorCold Start Kit
Tinted Safety Glass Diagnostic Pressure Test Points
Windshield Wipers/washers Downshift inhibitor
Utility Compartment Body Exhaust Heater
Controls Exhaust Muffler
Combined Switch Fuel Sight Gauge
Transmission Shift Selector Dual Brake system
/Teat Switch/steering Dlept Switch Emergency Brake System
Retarder Cintrol/Msin Beam transmission retarder
Manual Brake Switch Parking Brake
Dry/Wet Road Brake Switch Separate Steering and Body
Master Electric Dipping Switch Hoist Hydraulic System
Gauges electric: Reverse alarm
Air Pressure Reversing Light
Converter Temperature Headlights –quartz halogen
Engine Coolant Temperature Air Hom
Engine Oil Pressure Rear view Mirror
Speedmeter/MilemeterEngine Pan Guard
Tachometer/HourmeterTransmission Guard
Indicators-Light and Alarm Brake Mud Guard
Direction indicator Driveline Guard
Air Clearer Restriction Mud Flaps
Body Up Operator Arm Guard
Low Steering System Pressure Rock Ejectors
Headamps Main Beam Security Kit
Retarder”on” Side /Tail/Stop/Direction
Indicators and Warming Lights

Optional Equipment

Automatic Lubrication system Fire Extinguisher
Body Enlarged Capacity Spillguard Extension , folding
Body Wear Plates Tyres, 18.00r25**
Fast fuel Adaptor Radio

Weights

	kg	lb
Chassis,with hoists	16730	36942
Body,Standard	6270	13830
Net Weight	23000	50772
PAYLOAD,maximum	32000	70546
Maximum Gross Weight*	56000	121318

*Maximum permissible gross vehicle weight with options, Attachments, full fuel tank and payload

WEIGHT DISTRIBUTION Front Axle Rear Axle

Weight distribution	Front Axle	Rear Axle
Empty	48%	52%
Loaded	33%	67%

Serviceability

A wide ,roomy,two man , cab provides comfort operation and convenient training and maintenance.Air filters , hydraulic tank and its filters are acessible from a wide serbice platform on the right side of the cab.Engine oil and fuel filters are easily reached from ground level.
The transmission is installed in frame independently of engine and rear axle enabling servicing or removeal with minimum disturbance to other components.
Rear axle servicing is straightforward as differential, planetaries or axle shafts may be removed without jacking up the unit.Suspension units front or rear are replaceable with minimum of unit downtime.

SERVICE CAPACITIES	L	(US gal)
Engine Crankcase and Filters	34.0	(9.0)
Transmission and Filters	20.0	(5.3)
Colling System	104.0	(27.5)
Fuel Tank	330.0	(87.1)
Steering Hydraulic Tank	30.0	(8.0)
Steering Hydraulic system(Total)	47.0	(12.4)
Body Hydraulic Tank	83.0	(22.0)
Body Hydraulic and Brake Cooling System(Total)	121.0	(32.0)
Planetaries(Total)	30.0	(8.0)
Differential	57.0	(15.0)
Front Ride Strut(Each)	14.0	(3.7)
Rear Ride Strut(Each)	8.0	(2.1)
Power Take off	0.6	(0.2)