5watts 850MHz Outdoor Signal Repeater Waterproof
Outdoor Repeater 850mhz Output 5watts
Product introduction
1.Product summary
850mhz frequency-selecting micro repeater working for indoor or outdoor communication service blind area, it receives the base station's signal through the wireless mode to distribution system, and through a small base station antennas to send signals amplified out, meanwhile, mobile signal receiving, and go to the base station through the distribution system uplink, it can avoid communication service blind area indoor and outdoor effectively, barrage jamming, To provide stable and reliable signal for users in blind area, Enable users to enjoy the personal communication service with high quality. It is mainly used to cover the blind signal, poor call quality, slowly online rate and so on.
2.Place of application
Residential, office buildings, shopping malls, bars, underground parking, elevator and other communication blind area.
3.Characteristic function
Simulation of ALC
Wireless micro repeater with simulation of ALC function，gain automatic dynamic adjustment range up to 20dB, ensure the system with high reliability and high stability.
Function of Self-excitation detection
In the process of 850mhz micro repeater installed，it will be automatic detection, isolation between the donor antenna and the retransmission antenna, if the isolation does not meet the requirements of system installation, equipment malfunction indicator lamp providing instructions, and automatically reduce equipment gain, or shutdown. Until the device is working properly, protecting the safety of equipment and network without interference.
The function of Uplink and Downlink gain automatic linkage
After the System is installed and started, the system will automatically detect the input power, and control the output power, then calculate the downlink gain, automatic adjustment of uplink gain, maintain amplification balancing of system, realize uplink and downlink gain automatic linkage debugging, the gain of automatic control system is less than signal attenuation in path, ensure there is no any interference noise take into network.
Automatic installation indication function
The perfect working state indicator, 850mhz micro repeater different work state can be a good indicator. The installation is simple, to identify more clearly.
Local monitoring attenuation settings
Setting the equipment ATT digital attenuation in under the 850mhz system using local monitoring software according to the field applications , to adapt to the installation site due to gain strength of different requirements, make the application more convenient
Specification
Frequency
850mhz: 850mhz 824-849mhz 869-894mhz
Output power
TX: 35dBm±2dBm
RX: 37dBm±2dBm
ALC control
When in max output power, if increased less10dB input Level, the variation of the output power can be controlled within 2dB , When in max output power, if increased over10dB input Level, the variation of the output power can be controlled within 2dB or shut down repeater
Gain
85±2dB
Gain control range
≥30dB
Gain control step and error
Gain control step：1dB
Error range：0～10dB, error ≤±1dB；
10～20dB ,error≤±1dB；
≥20dB, error≤±1.5dB
Ripple in band
≤2.0dB/3.84MHz（peak value），Ripple in band≤4.0dB
Frequency error
≤±0.01ppm
Spectral emission
Meet 3GPP TS 25.106 demand
ACRR
Meet 3GPP TS 25.106 demand
Spurious emission
Meet 3GPP TS 25.106 demand
Outputintermodulation
Meet 3GPP TS 25.106 demand
Vector range error
EVM≤12.5%
PCDE
≤-35dB
Noise figure
≤6.0dB
Insulation test and prevent self-excitation
Support
Time delay
≤5.0us
VSWR
≤2.2
Ripple out of band
2.7MHz≤f_offset≤3.5MHz≤70dB
3.5MHz≤f_offset≤7.5MHz≤70dB
12.5MHz≤f_offset≤35dB
4.Indicator lamp status table
Work indicating lamp
Statu
Instruction
Power indicator lamp (Power)
Bright
The power supply is normal
Go out
Power failure
Downlink indicator lamp（DL/P）
Go out
Output power is too low
Twinkle
The output power is normal
Alarm indication lamp（Alarm）
Twinkle
Isolation is bad or antenna is not installed good
Go out
Normal work
Uplink indicator lamp（UL/P）
Twinkle
The output power is normal
Go out
Output power is too low
Product installation
Installed in the irrelevant personnel can't contact easily；
Installed in the cloth feeder and power supply easily；
To avoid the heat environment, installed in the ventilation；
Installed on the vertical wall or mast, to ensure good heat dissipation；
Wall-mounted installation mode, fixed the product bracket on the back of the installation , bracket hole location and expansion screw holes align fixed to the wall fixed hole a relative position as shown below;
Mast mounting mode, fixing the equipment bracket on the back of the product , using the hoop through the mounting bracket and fasten on the pole;
90.5mm
266.0mm
You can power up the product after the installation is complete, after all four indicator light on for 1 second, then after they all turn off, end, indicator lamp status in normal indication mode.
Repeater Complete set should include :
Attentions
The partition between two antennas, keep distance. Forbidden to open the equipment when the distance between antenna to equipment is less than 5 meters. Otherwise it will not work well.
Joint the equipment and antenna tightly, to avoid signal coverage effect is not good.
The original machine is equipped with 100V ~ 240V 50HZ three core AC power line, please note that the voltage range of input power.
The products work environment:
The equipment can work stably for a long time in the following conditions:
The temperature is -30 ℃ ~ +40 ℃, humidity below 95%;
Dustproof and waterproof: dustproof and waterproof grade: IP65;
Other supplier products
All supplier products
Same products
