HQFILTRATIONfilter element of water purifier industry prefe

Henan Uters International CO.,LTDlocated in North Third Ring Road,City area,Zhengzhou City,Henan Province,China,with elegant environment and convenience.market information delivered smoothly.UTERS LTD is a specialized Hydraulic Filtersx1dd01f6n,PALL FILTER company.

UTERS
Analysis of the noise caused by the failure of the hydraulic parts

Analysis of the noise caused by the failure of the hydraulic parts The failure of hydraulic components leads to noise and suction. It is one of the main reasons for the high noise of hydraulic pumps. The distributor of hydraulic pumps is also one of the most important components that easily cause noise. Here we will introduce in detail.
1. plunger pump or motor noise
(1) the phenomenon of air suction is one of the main reasons for the high noise of the hydraulic pump. When the air is mixed into the air, it is easy to form cavitation phenomenon in its high pressure area and propagate in the form of pressure wave, resulting in oil oscillation, resulting in cavitation noise. The main reasons are as follows:
(1) the oil filter of the hydraulic pump, the plugging of the inlet pipe or the high viscosity of the oil can cause the high vacuum at the inlet of the pump to make the air infiltrate.
(2) the damage of the oil seal on the shaft end of the hydraulic pump, the pilot pump, or the bad seal of the inlet pipe, resulting in the air entry.The oil level of the oil tank is too low to make the hydraulic pump suck into the air directly.When there is high noise in the work of the hydraulic pump, the above parts should be checked first and the problem should be dealt with in time. (2) the internal components of the hydraulic pump excessive wear, such as piston pump cylinder and valve plate, the plunger and the plunger hole with pieces of the wear and tear, injury, make a serious leak in the hydraulic pump, when the hydraulic pump output pressure and flow pulsation will produce small flow oil, causing high noise. At this time, the deflection angle of the pilot system variable mechanism can be appropriately increased to improve the effect of internal leakage on the output flow of the pump. The servo valve spool and the flow control piston of the hydraulic pump will also cause the piston to fluctuate during the movement due to local wear and tear. It will cause the fluctuation of the output and pressure of the hydraulic pump, resulting in larger vibration and noise at the outlet of the pump. In this case, the brush plating and replacement can be done for the elements with serious wear and tension.
(3) the flow plate of the hydraulic pump is also one of the most important components of the noise. Because of the surface wear or sludge deposition at the opening of unloading groove, the unloading slot will be shortened and the unloading position will be changed, resulting in the phenomenon of trapped oil, which will cause higher noise. During the normal repair process, the disc repaired by flat grinding will also have the consequences of shortening the unloading slot. If it is not properly slender in time, it will also cause great noise. During the assembly process, the large unloading groove of the distributor plate must be installed in the high pressure chamber of the pump, and the direction of its sharp angle must be opposite to the rotation direction of the cylinder block, otherwise, it will also bring great noise to the system. 2. hydraulic cylinder noise
(1) the air in the oil liquid or the air in the hydraulic cylinder is not completely exhausted, and the cavitation phenomenon is produced under the action of high pressure, which causes large noise. At this time, the air must be exhausted in time. (2) the oil seal of the cylinder head is too tight or the piston rod is bent. In the process of movement, the noise will be caused by the strength of the cylinder. At this time, the oil seal or the straightening piston rod must be replaced in time.
3. pipe noise
Too much pipe dead bending or fixed clip loosening can also produce vibration and noise. Therefore, arrangements should be in the pipeline to avoid dead corner Nagarze to loose to be timely tightening.
Noise of 4. overflow valve
The overflow valve is prone to generate high frequency noise, mainly due to the unsteady performance of the pilot valve, which is the noise generated by the air vibration caused by the high frequency oscillation of the pilot valve's front chamber. The main reasons are as follows:
(1) the air is mixed with the oil, and the cavitation phenomenon is formed in the front of the pilot valve, which causes the high frequency noise. At this time, the air should be exhausted in time to prevent the air from reentering the outside world. (2) during the operation of the needle valve, excessive wear is caused by frequent opening. The conical valve and the valve seat can not be tightly closed, causing the noise of the pilot flow to be unstable and generate pressure fluctuations. At this time, it should be repaired or replaced in time.
(3) the pressure regulating function of the pilot valve is unstable due to the fatigue deformation of the spring, which makes the pressure fluctuate and cause the noise, and the spring should be replaced at this time.
is focused on Good word of mouth Fuel Filter, FILTER ＩＮＳＥＲＴ quality Assurance, Good quality and good service line filter, oil filter element 100% genuine guarantee and other projects. even though in the rapid development of the project ,UTERS always stressed the balance between external opportunities and internal management, attaches great importance to the core competitiveness of enterprises to cultivate and shape. Our company take the value of customer service as the core competitiveness of enterprises, adhering to the honesty and integrity , the pursuit of excellence, respect individual for the corporate spirit, and strive to provide customers with integrity and reliable Hydraulic parts.

UTERSadheres to advance with the times and advocates to the service-oriented,faith-based, people-oriented management idea. With a belief of customer first to forge ahead , company insists on providing our clients with satisfying and best service ofpleated filter,oil filter element,

Other supplier products

	Lubricating oil filter,you can choose UTERSFILTER ELEMENTfo	Henan Uters International CO.,LTD is a professional company inLubricating oil filterx1dd01f6n,Filter Assembly. Since its inception,with innovative ...
	Henan Uters International CO.,LTD,an expert ofline filteran	line filterandLubricating oil filterof Henan Uters International CO.,LTDis favored by the majority of customers love, We have established long-...
	9Excellent quality Suction Filteris worth having	Henan Uters International CO.,LTD was founded in 10 years ago, After a period of rapid development, it has developed into a considerable size a...
	UTERS Sintered filterhave not only reliable quality but al	Henan Uters International CO.,LTDis a professional engaged in Henan Province,Zhengzhou City,City area,North Third Ring Road,Sintered filterx1dd01f6...
	Heilongjiang Province Excellent HYDAC FILTER	Henan Uters International CO.,LTDis a HYDAC FILTER,FILTERATIONin one large multi-functional integrated modern enterprise,and devote the high-qu...

供应产品

Same products

	古巴液氮供应罐KGSQ低温杜瓦瓶	卖方: Henan Tianzhidao Biological Technology Co., Ltd.	在生命科学研究中，液氮是较为常用的冷冻介质，储存它的容器则成了重要实验工具。实验进行中，为了样本的低温储存环境稳定，需要定期补液以保证充足供应，因为液氮易挥发，液氮量随时间推推移而减少。因此，为...
	Specification: 0.08mm-4mm	卖方: Changzhou Yuzisenhan Electronic Co., Ltd	Changzhou Yuzisenhan Electronic Co., Ltd. has convenient transportation in Wujin District, Changz...
	多哥细胞冷冻容器KGSQ液氮野外罐	卖方: 河南天之道生物科技有限公司	液氮罐的使用，覆盖科研、畜牧、美食、美容、冷冻配件等行业，但主要还是用于生物样本保存。 保存生物样本可细分为两大类，动物精液和实验细胞。两种用法适用容器不同，各有特色。冻精保存，要配圆提桶使用...
	White Fiberglass Surface, Packaging Type: Roll at	卖方: Jiangsu Zeyusen Carbon Fiber Technology Co., Ltd.	Fiberglass surface mat is mainly used in the surface layer of fiberglass merchandise, it has th...
	布隆迪细胞储存液氮容器 KGSQ 冷冻杜瓦瓶	卖方: Henan Tianzhidao Biological Technology Co., Ltd.	液氮罐的使用，覆盖科研、畜牧、美食、美容、冷冻配件等行业，但主要还是用于生物样本保存。 保存生物样本可细分为两大类，动物精液和实验细胞。两种用法适用容器不同，各有特色。冻精保存，要配圆提桶使用...