REFLOW OVEN

China reflow solderingtechnology is widely used in the field of electronic manufacturing. The components on the various boards used in our computers are soldered to the circuit board through this process. This PCB china reflow ovenmachine has a heating circuit inside to heat air or nitrogen. When the temperature is high enough, blow it to the circuit board where the component has been attached, so that the solder on both sides of the component will melt and bond with the motherboard. The advantage of this process is that the temperature is easy to control, oxidation can be avoided during the welding process, and the manufacturing cost is easier to control. Our reflow soldering oven is cheap and the soldering effect is good. It can guarantee the yield of electronic components and greatly improve the efficiency in the processing of electronic components.

As an experienced small reflow oven supplierin China, we provide different types of surface mount reflow oven (china smt reflow ovenmini or small reflow oven, etc) that are fit for various temperature zones, you can choose the most suitable one according to your own needs.

TYPES OF REFLOW OVEN

Reflow Oven D5 (Desktop)

D5 desktop/tabletop reflow oven worked with hot wind to solder PCB, support most normal components, LED, and kinds of IC. Crawler-type structure matched with five heating zones (3 up/ 2 down) can make inside temperature...

Reflow Oven L5

L5 nondetachable structure reflow oven worked with hot wind to solder PCB, support most normal components, LED and kinds of IC.Crawler-type structure matched with five heating zones can make inside te...

Reflow Oven D8 (Desktop)

D8 desktop/tabletop reflow oven worked with hot wind to solder PCB, support most normal components, LED, and kinds of IC. Crawler-type structure matched with eight heating zones can make inside temperature more accurate...

Reflow Oven L8

L8 nondetachable structure reflow oven worked with hot wind to solder PCB, support most normal components, LED and kinds of IC.Crawler-type structure matched with eight heating zones can make inside t...

Reflow Oven L12

L12 nondetachable structure reflow oven worked with hot wind to solder PCB, support most normal components, LED and kinds of IC.Crawler-type structure matched with twelve heating zones can make inside...

Reflow Oven MR30

TronStol MR30 is the newest mini reflow oven.It is full convection oven(tubular heaters and fan).The heat distribution and absorption are same for dark and light components. After the reflow oven preh...

HOW IS A REFLOW OVEN CONFIGURED

Theoretically ideal temperature curve consists of preheating zone, heat preservation zone (active zone), heating zone (reflow zone) and cooling zone. The first three zones are heated, and the last zone is cooled.

①In the preheating zone, heat the board from room temperature to around 150°C. Preheating is to activate the solder paste and to avoid the rapid high temperature heating during the immersion of tin, which will cause defective parts. The goal of this area is to heat the board at room temperature as soon as possible, and the heating rate should be controlled within an appropriate range. If the temperature rises too fast, thermal shock will occur, and the boards and components may be damaged; if the temperature rises too slowly, the solvent will not evaporate adequately and affect the soldering quality.

②Insulation zone (active zone), generally 150°C～180°C, within 200°C. The activity of the solder paste is the strongest in this temperature range, and it is maintained for about 90s. The main purpose of the insulation stage is to stabilize the temperature of the internal components of the reflow oven, and to minimize the temperature difference of each part. Stay in this area for enough time to make the temperature of the larger components catch up with the temperature of the smaller components, and ensure that the flux in the solder paste is fully volatilized. At the end of the insulation stage, the oxides on the bonding pad, solder balls and component pins are removed under the action of the flux, and the temperature of the entire circuit board is also balanced.

③In the heating zone (reflow zone), the solder paste begins to melt and the time is between 60s and 90s. In this area, the heater temperature is set to the highest, so that the internal temperature quickly rises to the peak temperature. The peak temperature of the reflow curve is usually determined by the melting point temperature of the solder paste and the heat-resistant temperature of the boards and components. The peak temperature also varies depending on the solder paste used. Generally, the maximum temperature of lead-free solder paste is 230°C-250°C, and the maximum temperature of lead-containing solder paste is 210°C-230°C. Pay attention to the time in the heating zone not to be too long to prevent damage to the inner wall of the reflow oven, damage to electronic components or scorching of the circuit boards.

④In the cooling zone, quickly reduce the temperature to solidify the solder paste. In this area, the temperature is cooled to below the solid phase temperature to solidify the solder joints. The cooling rate will have an impact on the strength of the solder joints. If the cooling rate is too slow, it will cause excessive eutectic metal compounds to be produced, and a large grain structure will appear at the solder joints, making the strength of the solder joint lower.

REFLOW OVEN FEATURES

Reflow oven is a equipment for soldering components to a PCB board. It relies on the action of hot air flow on the solder joints. The glue-like solder paste undergoes a physical reaction under a certain high temperature air flow to achieve SMD soldering. The reason why it is called "reflow soldering" is that Because the gas circulates in the reflow oven to generate high temperature to achieve the purpose of welding.

4. It has a self-positioning effect. When the component placement position deviates to a certain extent, due to the surface tension of the molten solder, when all the solder ends or the pins and the corresponding pads are wetted at the same time, they are automatically pulled under the action of surface tension return to approximate target position.

If you want to know more types of china smt line machine, please visit our website.

As one of smt equipment manufacturers, we will do our best to meet all the needs of customers.

Другие товары поставщика

	REFLOW OVEN	China reflow solderingtechnology is widely used in the field of electronic manufacturing. The components on the various boards used in our computer...
	IC Camera	IC Camera is mainly suitable for Trosntol A1 pick and place machine, which is responsible for the scanning and positioning of IC. It is an indispen...
	About Auto Loader SL400	It is used for the board loading device of SMT production line circuit boards. It can be used with the standard material box to automatically send ...
	SMT Equipment in Communication	The era of the Internet is inseparable from the popularization of communication equipment. SMD machine for mobile repairingemerge as the times requ...
	PROTOTYPE SMT LINE	If you are a professional PCB designer, are you tired of manually mounting components？It really costs a lot of time. It is recommended that you use...

Все товары поставщика

Похожие товары

	cuba Резервуар для подачи жидкого азота Криогенная колба Дьюара KGSQ	Продавец: Henan Tianzhidao Biological Technology Co., Ltd.	В исследованиях в области медико-биологических наук жидкий азот является широко используемой замо...
	Specification: 0.08mm-4mm	Продавец: Changzhou Yuzisenhan Electronic Co., Ltd	Changzhou Yuzisenhan Electronic Co., Ltd. has convenient transportation in Wujin District, Changz...
	Контейнер для заморозки ячеек Того KGSQ Полевой резервуар с жидким азотом	Продавец: Хэнань Тяньчжидао Биотехнология Лтд.	Использование резервуаров с жидким азотом охватывает научные исследования, животноводство, делика...
	White Fiberglass Surface, Packaging Type: Roll at	Продавец: Jiangsu Zeyusen Carbon Fiber Technology Co., Ltd.	Fiberglass surface mat is mainly used in the surface layer of fiberglass merchandise, it has th...
	Контейнер с жидким азотом в Бурунди для хранения клеток Крио-дьюар KGSQ	Продавец: Henan Tianzhidao Biological Technology Co., Ltd.	Использование резервуаров с жидким азотом охватывает научные исследования, животноводство, делика...