Hydraulic Liner Hanger Tie-Back Assembly

The tie-back assembly is a special cementing tool for tieback operation.

Tieback equipment allows existing liners with a receptacle to be extended to the surface or farther up hole, and provides a high-pressure seal at the top of a cemented or uncemented liner. TIW offers variety of tieback seal nipples and tieback packers to accommodate liner top extension and remedial operations. Today, some new types of drilling liner tieback equipment are developed due to the annular gas channeling in high-pressure oil-gas well even after tie back cementing.

Tie back liner procedureof Hydraulic Liner Hanger Tie-Back Assembly

Measure and drift the casings carefully and clean all the threads.

Calculate the kelly-up of the casing (the particular part of the last casing which is above the rotary table) and arrange the casing string.

Prepare several casings, which are approximately 0.5m shorter than the others and convenient for kelly-up calibration. (The actual kelly-up is not equal to the calculated value due to measurement error and the remaining threads of the casings.)

Connect the milling shoe and trip in. Polish the inner surface of the polished bore receptacle, make sure there is no debris.

Note the depth of the milling shoe when it reaches the top of the seal assembly (judge from the changes on pressure and WOB). Then lift the drill string for 1m.

Use a drilling rate of 40～50rpm and a normal flow rate. Slowly lower the drill string. Polish the inner surface of the polished bore receptacle twice or three times. Each time polish 3～4min. During the last polishing, apply an additional load of 2～3t when the torque suddenly increases (the milling shoe reaches the top of the seal assembly) during the last polishing. Polish for another 2~3min and note the depth of the milling shoe, which is an important clue for the casing setting depth.

Circulate with high flow rate for 5min.

Trip out and check the milling shoe. If there is a circle of polished trace and the diameter is equal to the I.D. of the left thread on the seal assembly, then the milling shoe have reached the bottom of the polished bore receptacle.

Features of Hydraulic Liner Hanger Tie-Back Assembly

With the guide shoe and circulate bore, it can stab into polished bore receptacle before cementing, more convenient than conventional cementing which pumps down cement before stabbing.

With its streamline shape, the guide shoe can stab into polished bore receptacle easily.

The Tieback Seal Assembly with three stacks of molyglass seal is designed for high-pressure and high-temperature liner tieback completions. Available in seal length is 1.2m.

As one of the top reliable liner hanger companies in China, Saigao has been devoted in the production of hydraulic liner hanger products. Drop us messages for any query to know more about Saigao and Saigao products.

Technical Parameters ofHydraulic Liner Hanger Tie-Back Assembly

Specifications, mm	Φ177.8	Φ127.0
Sealing capacity, MPa	25	25
Heat-proof Rating, ℃	120	120
Available Sealing Length, mm	1200	1200
	Φ155	Φ108

,

As one of the most professional oil well equipment manufacturers, Saigao Groupprovides oilfield cementing tools, tie back receptacle, tie back casing, liner hanger assembly, hydraulic hangercasing tie back, tie back liner and etc. Saigao products are not only popular in China, but also exported to Russia, Brazil, Australia, South Africa and other countries and regions.

Другие товары поставщика

	Non-rotating Stabilizer	Non-rotating stabilizer(rubber sleeve stabilizer) is able to avoid blade wear and wall damage during. The non-rotating stabilizer consists of mandr...
	Choke Manifold	Choke manifold for salecontrol and implementation of oil and gas pressure control technology. In case that the BOP is off, the pressure at the bott...
	Drill Collar and Spiral Drill collar	Drill collar is mainly used to provide bit weight to drill bit so that drill pipe is in tension. Especially drill collar can keep drill bit central...
	F500 Single-acting Mud Pump	F500 single-acting drilling rig mud pump equipment has two surfaces which can bear high strength to ensure high efficiency of the operation. We ri...
	MZ Type Die Collar	MZ die collar is a special external fishing tool that engages with the dropped tubular s such as drill pipes casing and oil tubing, by tapping on t...

Все товары поставщика

Похожие товары

	Gr50 Pneumatic Conveying Equipment/Cast Iron Blow Through Airlock Valve	Продавец: Greentech International (Zhangqiu) Co., Ltd	Rotary feeder is also called rotary pocket feeder or airlock machine.The structure of normal rota...
	Gr400 Pneumatic Conveying Equipment/Pneumatic High Pressure Conveying Equipment	Продавец: Greentech International (Zhangqiu) Co., Ltd	Rotary feeder is also called rotary pocket feeder or airlock machine.The structure of normal rota...
	Greentech GR220 Electric Star Feeder | Rotary Airlock Valve Seals for Pneumatic Conveying Systems 6 Months Warranty 310kg	Продавец: Greentech International (Zhangqiu) Co., Ltd	Customized Support: Tailored solutions for industrial machinery needs. High-Quality Electric P...
	Intelligent Precision Glue Control System	Продавец: 855005	Intelligent Precision Glue Control System The Golden Horse GM-4020 is an intelligent glue concen...
	JM-5416D Automatic Rigid Box Making Machine	Продавец: 855005	JM-5416D Automatic Rigid Box Making Machine The JM-5416Dintelligent visual fully automatic box m...