round drill collar
round drill collar
There are different kinds of drill collars,including round drill collar,spiral drill collar,non-magnetic drill collar,square drill collar and so on.Ordinary drill collar is the circular cross section, the center has a water hole,the wall thickness is larger,the nozzle is smaller, the weight of per unit length is greater than the size of drill pipe almost 4- 5 times .The majority of drill collar is thread processing directly on the pipe body , but some of them also use the replaced joint.
(1)Eccentric-weight drill collar is an effective anti-deviation drilling tool,with high drill pressure used in oblique areas,rectifying oblique as well.
(2)When drilling directional wells eccentric-weight drill collar is an effective tool to reduce oblique or straighten the well hole using high drilling pressure.
(3)Eccentric-weight drill collar has the advantages of simple structure,convenient use,connected directly to common drill collar without centralizers,greatly convenient for sinking in,fishing and milling operations.
(4)Eccentric-weight drill collar runs downhole safely,danger of leakage or bit freezing hard to appear.
(5)Pay much attention to avoid mud balling and prevent effect of anti-deviation .
CHEMICAL COMPOSITION
Drill Collar Specification |
||||||||
Thread Type |
Length |
Diameter of shoulder guide Angle |
Reference bending strength ratio |
|||||
mm |
inch |
mm |
inch |
mm |
inch |
|||
NC23-31 |
31/8 |
11/4 |
9150 |
30ft |
||||
NC26-35(23/8IF) |
31/2 |
11/2 |
||||||
NC31-41(27/8IF) |
41/8 |
2 |
||||||
NC35-47 |
43/4 |
2 |
||||||
NC38-50(31/2IF) |
127 |
5 |
21/4 |
121 |
||||
NC44-60 |
6 |
21/4 |
9150or9450 |
30ftor31ft |
||||
NC44-60 |
6 |
213/16 |
||||||
NC44-62 |
61/4 |
21/4 |
||||||
NC46-62(4IF) |
61/4 |
213/16 |
150 |
|||||
NC46-65(4IF) |
61/2 |
21/4 |
||||||
NC46-65(4IF) |
61/2 |
213/16 |
||||||
NC46-67(4IF) |
63/4 |
21/4 |
||||||
NC50-67(41/2IF) |
63/4 |
213/16 |
||||||
NC50-70(41/2IF) |
7 |
21/4 |
||||||
NC50-70(41/2IF) |
7 |
213/16 |
||||||
NC50-72(41/2IF) |
71/4 |
213/16 |
||||||
NC56-77 |
73/4 |
213/16 |
||||||
NC56-80 |
8 |
213/16 |
||||||
65/8REG |
81/4 |
213/16 |
||||||
NC61-90 |
9 |
213/16 |
||||||
75/8REG |
91/2 |
3 |
||||||
NC70-97 |
93/4 |
3 |
||||||
NC70-100 |
254 |
10 |
3 |
|||||
85/8REG |
11 |
3 |
||||||
Note: 1.Drill collar thread type: NC-Digital IF-Internal flat type REG-Normal type |
||||||||
In addition, our company can produce the drill collar and spiral drill collar, which can also produce the special specifications of the drill collar and the high efficiency and wear-resisting lengthening drill collar |
cutting depth |
Lead ±25.4 |
|||
mm |
in |
A(mm) |
B(mm) |
mm |
86 |
679 |
|||
914 |
||||
4~4 1/8 |
914 |
|||
4 1/2~5 1/8 |
965 |
|||
5 1/4~5 3/4 |
1067 |
|||
5 7/8~6 3/8 |
1067 |
|||
6 1/2~7 |
1168 |
|||
7 1/8~7 7/8 |
1626 |
|||
8~8 7/8 |
1727 |
|||
9~9 7/8 |
1829 |
|||
10~10 7/8 |
1930 |
|||
11 |
2032 |
Advantages of Drill Collar Production Process:
In the process of heat treatment, the drill collar has added a special normalizing process, which makes the thread part grain more refined, enhances the drill collar thread strength, and effectively improves the service life of the drill collar.
Sreel Mark |
Chemical Composition % |
||||||||
C |
Si |
Mn |
P |
S |
Cr |
Mo |
Cu |
Al |
|
4145H |
≤0.03 |
≤0.03 |
≤0.2 |
||||||
Other Elements:N≤0.015,Ni≤0.5 |
Drill Collar Mechanical Performance |
||||||||
Drill Collar Outside Diameter Range |
Yield Strength |
Tensile Strength |
ElongationA% |
HB |
Charpy ImpactAkv J |
|||
mm |
in |
MPa |
Psi |
MPa |
Psi |
|||
3-1/8~6-3/4 |
≥758 |
≥110000 |
≥965 |
≥140000 |
≥13 |
285~341 |
≥54 |
|
7~11 |
≥689 |
≥100000 |
≥930 |
≥135000 |
≥13 |
285~341 |
≥54 |
|
Under special conditions, the impact work of the charpy can be determined as greater than 70J according to the supply and demand |
Size |
Code |
Thread |
Length(mm) |
Weight(kg) |
||
3-1/8 |
NC23-31 |
NC23 |
9140 |
298 |
||
3-1/2 |
NC26-35 |
NC26 |
9140 |
364 |
||
4-1/8 |
NC31-41 |
NC31 |
9140/9450 |
474/490 |
||
4-3/4 |
NC35-47 |
NC35 |
9140/9450 |
674/697 |
||
5 |
NC38-50 |
NC38 |
9140/9450 |
725/749 |
||
6 |
NC44-60 |
NC44 |
9140/9450 |
1125/1163 |
||
NC44-60 |
9140/9450 |
1022/1056 |
||||
6-1/4 |
NC44-62 |
NC44 |
9140/9450 |
1237/1279 |
||
NC46-62 |
9140/9450 |
1134/1172 |
||||
6-1/2 |
NC46-65 |
NC46 |
9140/9450 |
1352/1398 |
||
NC46-65 |
NC50 |
9140/9450 |
1249/1291 |
|||
6-3/4 |
NC46-67 |
NC46 |
9140/9450 |
1471/1521 |
||
7 |
NC50-70 |
NC50 |
9140/9450 |
1597/1651 |
||
NC50-70 |
9140/9450 |
1494/1545 |
||||
7-1/4 |
NC50-72 |
NC50 |
9140/9450 |
1625/1680 |
||
7-3/4 |
NC56-77 |
NC56 |
9140/9450 |
1895/1960 |
||
8 |
NC56-80 |
NC56/6-5/8REG |
9140/9450 |
2040/2109 |
||
8-1/4 |
6-5/8REG |
6-5/8REG |
9140/9450 |
2188/2263 |
||
9 |
NC61-90 |
NC61 |
9140/9450 |
2658/2748 |
||
9-1/2 |
7-5/8REG |
7-5/8REG |
9140/9450 |
2954/3054 |
||
9-3/4 |
NC70-97 |
NC70 |
9140/9450 |
3127/3234 |
||
10 |
NC70-100 |
NC70 |
9140/9450 |
3308/3421 |
||
11 |
8-5/8REG |
8-5/8REG |
9140/9450 |
4072/4210 |
||
Mechanical properties:<7 inch Drill Collar:Yield Strength≥758MPa,Tensile Strength≥965MPa,Four times elongation≥13%,Impact energy Ak≥54J,(Single impact work≥47J,Average≥54J)Hardness range 285HB~341HB≥7inch Drill Collar:Yield Strength度≥689MPa,Tensile Strength≥931MPa,Four times elongation≥13%,Impact energy Ak≥54J,(Single impact work≥47J,Average≥54J) Hardness range 285HB~341HB |
Отправить запрос, связаться с поставщиком
Другие товары поставщика
high tensile strength | If you have any question on Grade Hy Sucker Rodand Api Solid Sucker Rods. We will give the professional answers to your short questions. Grade HY S... | |
API grade d sucker rod | Grade D Sucker Rodwith chinese manufactuer API grade d sucker rod Hot sale various high quality Grade D Sucker Rod and 1" Grade D sucker rod from C... | |
Tapered Thread Sucker Rod | Tapered Thread Sucker Rod It is a sucker roddesigned specially for the PCP pump, and the taper thread is designed according to the drill pipe thre... | |
Spray Anti-corrosion Sucker Rod | Spray Anti-corrosion Sucker Rod It is a kind of manufacturability anti-corrosion sucker rod, the rod surface spraying a layer of special anti-corro... | |
Grade D Sucker Rod | Grade D Sucker Rod Hot sale various high quality Grade D Sucker Rod and 1" Grade D sucker rod from China leading manufacturer. Our products are ef... |
Похожие товары
KLUBER LECTRIC KR 44-102 1KG Grease | Продавец: Guangdong Juguangheng Automation Equipment Co.,Ltd. | NSK LR380G/PC 20PC,50PC/Carton NSK AS280G/PC 20PC,50PC/Carton NSK LG280G/PC 20PC,50PC/Carton N... | |
KLUBER ISOFLEX TOPAS NCA52 75G Grease | Продавец: Guangdong Juguangheng Automation Equipment Co.,Ltd. | “LUBE FS-2-7 700G” LUBE FS-2-4 400G LUBE FS-2-2 200G LUBE FS-1-7 700G LUBE MY-2-7... | |
Kluber ISOFLEX TOPAS L 32CN 1KG Grease for Pick and Place Machine | Продавец: Guangdong Juguangheng Automation Equipment Co.,Ltd. | NSK LR380G/PC 20PC,50PC/Carton NSK AS280G/PC 20PC,50PC/Carton NSK LG280G/PC 20PC,50PC/Carton N... | |
BQH 72-102 grease 1KG for Pick and Place Machine | Продавец: Guangdong Juguangheng Automation Equipment Co.,Ltd. | N990pana-023 Panasonic MP Grease Kluber Isoflex Nbu 15 Grease Afc Lubricant K3036c K48-M3856-0... | |
LDS 18 1kg kluber Lubricants for SMT Machine | Продавец: Guangdong Juguangheng Automation Equipment Co.,Ltd. | We are a professional supplier of SMT production line product. We supply various SMT Machine (SMT... |