.

SAC305 Lead Free Wave Silver Soldering Bar

Product DetailsBBIEN LF-03 SAC305 lead free wave silver soldering barProduct’s Introduction forSAC305BBIEN LF-03 SAC305(Sn96.5Ag3.0Cu0.5)is a lead-free solder according to ISO9001:2008 which can replace eutectic or almost eutectic tin/lead or tin/lead/silveralloys.BBIEN LF-01 SAC305 alloy solder bar is manufactured from pure metals and hasbeen developed to eliminate the use of tin/lead alloys in all existing production processesin electronics manufacturing and guarantees a lead-free wave soldering process.Products Characteristics AdvantageGood wetting characteristicsMelting range of 217 to 222°CLonger service life due to reduced copper contentLower cost than eutectic SnAgCu alloy due to 0.8%lower silver contentYield–Best in class yield,out performs all Sn/Cu based materialsWetting speed–fast wetting,in back to back tests 0.65s compared to 1.00s,for Sn/Cu based materialsDross generation–Low dross generation delivered by Vaculoy alloy conditioningExcellent solderability due to fast wetting speedVery good drainage,has lower levels of bridging compared to Sn/Cu alloysDelivers excellent performance across a wide range of Flux technologies.The proprietary Vaculoy process is a highly effective method for removing includedoxides from solder.This is extremely important because included oxides generateexcessive drossing and increase the viscosity of the solder.Solder with higher viscositycan result in increased soldering defectsApplication Notes:On changing to lead-free production the temperature profile and process conditions for this alloy-like for any other lead free alloys,too-must be adjusted.The resulting solder joints will have comparable or even better characteristics than solder joints,which were made with Sn/Pb solders.During the use in a solder bath the copper content increases with the consequence,that the liquidus of the alloy is rising,causing soldering defects Therefore a regular analytical control of the solder composition is necessary in order to maintain the copper content below 1%.The use of BBIEN LF-03 SAC305 as wave solder requires a solder bath temperature of approx.260 to 265°C.The use of inert gas means a significant extension of the process window.The wetting of the solder is made easier and on exit from the wave,no excess solder remains attached to the components.BBIEN LF-03 SAC305 lead free silver wave solder bar can also be used in selective soldering systems.PackingSpecificationSn99-Ag3.0-Cu0.5 bar soldersAppearanceLucent,no dirt on surfaceSizeLength×wideness×Thinckness×Weight(L×W×T×W):800px×45px×37.5px×0.7kg/pc 20kg/cartonUsageBBIEN LF-03 SAC305(Sn96.5Ag3.0Cu0.5)Pb-free wave soldering bar is suitable for wave soldering and surface mount applications for electronic assemblers interested in implementing a lead-free process.A solder pot temperature of 255-265°C(491-509°F)is recommended.For suitable wave solder fluxes,please see our selector guide.Lead free Reclaim services including dedicated lead free containers are also available.Please consult BBIEN sales office.AVAILABILITYBBIEN lead free soldering bar available in 0.9kg bars,feeder Ingots and autofeed wire.Most products are shipped strapped and palletized or packed in corrugated cardboard box with no remarkable damages in appearanceRECOMMENDED CONDITIONS OF USEWave Soldering:The low copper content is advantageous for wave soldering because longer operating times of the solder bath can be achieved.By dissolving of copper from the PCB the copper content increases. Using ECOLOY®TSC305 means that it takes longer until the critical limit of 1.0%is reached. The use of BBIEN LF-03 SAC305 silver solder bar as wave solder requires a bath temperature of approx.265°C.Depending on PCB type and types of components, the optimum of the process conditions must be determined. The usage of inert gas brings a considerable extension of the process window.The wetting of the solder will be easier, and there will be no excessive solder on the PCBs when leaving the wave.Moreover the formation of dross will be minimised considerably.Wave Soldering Fluxes:In general,all conventional fluxes like BBIEN LF-01 flux is suitable for the lead free soldering process.The flux solid content should be high enough.Due to the increased preheating and wave temperature a better activity respectively temperature stability is an enormous advantage.Rework und Hand Soldering:Adjusted flux content assures a proper soldering for rework and repair.The temperature profiles,which were made for tin/lead/silver alloys,must be adjusted due to the higher melting point(+34°C compared with Sn/Pb eutectic).In case that components or PCBs have a lead containing coating,the solidus of the new alloy will be reduced to the solidus of the eutectic Sn/Pb/Ag alloy.Technical DatasheetBBIEN LF-03 SAC305 lead free wave silver soldering barTachnical SpecificationBBIEN LF-03 SAC305 silver solder bar complies with all requirements of RoHS Directive (Article 4.1 of the European Directive 2011/65/EU). Alloy specification for maximum Lead (Pb) Content = 0.07%. SAC alloy is also available in Ultra Low Lead (ULL) version which contains a maximum of 0.05% Pb. All alloy properties remain the same for SAC ULL.CharacteristicSAC 305Melting Point217-219ºC(423-426ºF)Density37.37 g/cmTCE (Range 20-100ºC)micrometers / M / ºC21.9Specific HeatCapacity0.232 J/g KHardness14.1 HVSAC305 solder bar materials charersterisCharacteristicSAC 305Melting Point217-219ºC(423-426ºF)Density37.37 g/cmTCE (Range 20-100ºC)micrometers / M / ºC21.9Specific HeatCapacity0.232 J/g KHardness14.1 HVLead free solder items of BBIENNo clean lead-free soldermelting point °CTensile strengthelongation reat%expansion rate%DiameterApplicationSolder wire alloySolder bar/block alloySolder paste alloySolder powder alloySn99.3Cu0.7227304570≥0.1mmlow cost, the most commonly used;Lead-free solder for general weldingyesyesyesyesSn96.5Ag3.0Cu0.5217405878≥0.1mmhigh cost, relatively bright spot;high performenceCan be excellent for demanding welding yesyesyesyesSn99.0Ag0.3Cu0.7Sn64Bi35Ag1189405070SMT,PCBnotnotyesyesSn62Pb36Ag2189385475SMT,PCBnotnotyesyesSn42Bi≥0.5mmHigh costyesyesyesAdvantage And ServiceBBIEN LF-03 SAC305 lead free wave silver soldering barProducts AdvantageLF-03 SAC305 lead free offers excellent solderbility,wettibility and reliability among Pb free solder bar,it is available in a wide product lineup according to the required soldering temperature.Thanks to BBIEN long-term unremitting R&D for solder technique,until now,BBIEN have the following high-tech solder product for different lead free alloy.LF-03 SAC305 lead free tin-silver-copper high temperature solder bar can be not only applied to tradional electronics pcb,electronics soldering,but also its application for some new hi-tech industry,semiconductor.LED, aerospace, automotive.LF-03 SAC305 lead free SAC305 217 degree Celsius RoHS standard Pb free tin based soldering bar can be packaged 20kg per ctnVery good constant flow and wetting,clear and transparent residuesBBIEN is specialized in soldering industry from 2000,known as a experienced tin lead and lead free solder bar manufacturer,whose products are made in China,since then,BBIEN pays high attention to Research and Development,continuous technical innovation for pb and pb free solder bar industry,until now,we accumulate much valuable experience,five senior solder wire engineers operate a specialized reflowing solder wire production.OEM can be discussed,we will use our own label if customers have no other requirement.No clean lead-free soldermelting point°CTensile strengthelongation reat%expansion rate%DiameterApplicationSolder wire alloySolder bar/block alloySolder paste alloySolder powder alloySn99.3Cu0.7227304570≥0.1mmlow cost,the most commonly used;Lead-free solder for general weldingyesyesyesyesSn96.5Ag3.0Cu0.5217405878≥0.1mmhigh cost,relatively bright spot;high performenceCan be excellent for demanding weldingyesyesyesyesSn99.0Ag0.3Cu0.7Sn64Bi35Ag1189405070SMT,PCByesnotyesyesSn62Pb36Ag2189385475SMT,PCByesnotyesyesSn42Bi≥0.5mmHigh costyesnotyesyesCertificates availableBBIEN can share the datasheet for our product to our clients.Certificates of compliance,SGS,ISO and COA,MSDS,are available.We are tyring to make our product quality system more and more complete,BBIEN also appreciate your precious suggestion.Both pre-sale and after-sale,BBIEN have skilled person to follow-up our client,reply answer for reasonable price,relevant quality standard,products data informations, shipping for your questions skillfully, quickly, technical support is available.Shipping AdvantageMutiple-transportation oversea shipping ways by ari,by sea,by train and truck road way ensuring the shipment can arrive at destination all around the world safety,quickly and efficiently.Shipment can be deliveried once placing order 2 to 10 working days.Shipment will be regular go through local custom and its warehouse,BBIEN has own specialized shipping team and operators agent all over the world.ServiceWhen you send us message,BBIEN will feedback you general within 2 working hours.Our customer service or sales person will be match with you above 10-24hours.And solve your problem on solder products.OEM is available according to your own logo.Normal RAQ1.Do I need to pay the charge for sample?We offer the small free sample for testing,but the courier charge should be paid by your side.2.How about your product quality,guaranteed?Our products through strict quality control and inspection before leave factory,and haspassed the SGS.3.What is your delivery time?2-3days for delivery sample2-3days for standard goods in stock5-7days for normal order7-12days for customize order4.Any other special metal items that you make too?We produce Zn wire,Sn wire,Mo wire,Indium wire;We still make special metal alloy:e.g.,Sn-Bi,Ag-Al,Sn-Sb,Sn-Ag,Ge metal;In metal etcPayment way:A variety and flexible of payment terms,T/T,western union,paypal,L/C can be acceptable.Others:Prodution ability:6tons each day for normally solder wire diameter above 1.0mm,packing 1kg/spoolDelivery time:within 7working days after confirming payment infos.Why choose us?*We are the manufacturer of solder items,special metalalloy,you can buy the suitable products you need at reasonable prices.*Our customer service personnel will provide you with our competitive quotation as wellas expedite your orders&provide you with any assistance you may require.*Sales engineers are available to offer help recommending the most suitable products for your application and solve problems once you find problem to use our products.*We can accept OEM or ODM,use your brand name and logo on the solder reel!*Promptly delivery and small sample order is available.Return back to societyBBIEN also participates public benefit activities,return back to society.We support and want to create a environmental friendly society together with people.We also try our best to help someone who need us.


Отправить запрос, связаться с поставщиком

Кому: SHENZHEN BBIEN TECHNOLOGY CO.,LTD
Ваш E-mail:
Текст письма:


Send to other suppliers

Другие товары поставщика

Product DetailsSn/Pb lead alloy bar solder Sn70Pb30 Sn40Pb60 Sn30Pb70 BBIEN tin-lead alloy bar solder IntroductionBBIEN Sn70Pb30,Sn40Pb60 30/70 20/...
Product DetailsMiddle and low temperature lead solder paste BBIEN TL-02 Sn62Pb36Ag2Brief IntroductionBBIEN solder paste manufacturer has enough tec...
Product DetailsHigh quality pure cobalt wire 0.3mm~2mmIntroduction for cobalt wireBBIEN supplies 99.9% and 99.99% pure cobalt wire, cobalt wire, pu...
Product DetailsMid temperature no clean solder paste LF-04 Sn64.7Bi35Ag0.3Brief IntroductionBBIEN is a specialized solder pastes manufacturer in Ch...
Product DetailsBBIEN LF-03 SAC305 lead free wave silver soldering barProduct’s Introduction forSAC305BBIEN LF-03 SAC305(Sn96.5Ag3.0Cu0.5)is a lead-...
Все товары поставщика

Похожие товары

Aluminum Bicycle Headset Stem WH-09B
Aluminum Bicycle Headset Stem WH-09B Продавец: Ningbo City Haishu Mateaial Alloy/Steel Fork Clamp Diameter 22.2mm or 21.1mm Handleb...
Шэньчжэнь PCB Шэньчжэнь производство печатных плат, закупка компонентов, сборка печатных плат, электронное контрактное производство, производство, закупка компонентов, сборка печатных плат, электронно
Шэньчжэнь PCB Шэньчжэнь производство печатных плат, закупка компонентов, сборка печатных плат, электронное контрактное производство, производство, закупка компонентов, сборка печатных плат, электронно Продавец: PCB Ассамблеи производитель-STG Электронные STG Electronic является ведущим профессиональным производителем сборки печатных плат в Китае, кот...
PILZ | PNOZ X1 3S/1O
PILZ | PNOZ X1 3S/1O Продавец: 761982 General Electric (USA)SNAT 634 ☞☞☞☞☞IM315 Interface Module Huge Inventory||Top Quality ||24/7 Fas...
FESTO | SMEO-1-S-LED-24-B
FESTO | SMEO-1-S-LED-24-B Продавец: 761982 General Electric (USA)SNAT 634 ☞☞☞☞☞IM315 Interface Module Huge Inventory||Top Quality ||24/7 Fas...
TURCK | Ni8-M18-LiU
TURCK | Ni8-M18-LiU Продавец: 761982 General Electric (USA)SNAT 634 ☞☞☞☞☞IM315 Interface Module Huge Inventory||Top Quality ||24/7 Fas...