Hot Air Welding Machine
Automatic Banner Welding Machine(Just For Your Reference)Please r ead t he introduction carefully before using machine and keep it wellAPPLICATIONThe automatic welding machine is designed to weld plastic materials. The automatic welding machine can weld advertising inkjet fabric, inkjet cloth, light box cloth, thick PVC cloth, mesh cloth, tarpaulin and other PVC, PE, DHPE, LDPE, EVA, Pp plastic materials that can be hot melted. It is small, light and easy to operate. It is equipped with temperature feedback sensor. The sensor can always monitoring the temperature of the outlet to keep a constant temperature. It uses advanced PID control technology, and adjust the power to make the temperature more constant automatically,the fluctuation is within 1 degrees. This function can make the welding result stronger. It also can avoid leakage. This machine is more suited to fast welding of large banners.1.Temperature knob 2. Wind speed knob 3. Walking speed knob4. Reset knob 5. Temperature feedback sensor 6.operation handle7. Wing sheath 8.Heat gun 9. Nozzle 10.Press wheel 11.Carry handrail12.Carry handrail 13.Actual temperature 14.Set temperature 15.Walking speed 16.Turn up temperature button 17.Turn down temperature button ACCESSORIES 1. A 10m power cable. 2. A Wrench3. One piece of manual5. Video CDOperation:1.First, make the picture smooth and tight, take joiner to accurate (about 2-4cm), fixed edges with tape or glue on the ground.2.Set temperature:connect power, turn on the temperature knob (the golden knob)until it click,and then press▲(▲for up ▼for down). In general, the temperature is between 350-400℃,Or to know it the temperature is ok,we can taking some waste banners to aligned nozzle to test, If it can be melted immediately, This temperature is the one you need and to set.if not strong just increase temperature,if too hot,reduce temperature.check photo below:3.Set wind speed：in general,we put wind speed to the largest.so just put wind speed to the Maximum is ok.4.Set walking speed:Then turn on waling knob to adjust the speed, generally marked on the knob points to the location between 3 from 4.5.Start welding:when actual temperature of the display screen reaches temperature that you set, we can begin to weld.put operation handrail(at end of the machine)to left,machine begin to work automatically.At begin of weld,we should use one hand to take one banner up,then put nozzle between two banners,check photo:6.During welding,let hot air nozzle between two overlap pieces. And be make sure hot air nozzle and Rubber wheel walk in straight line.if not,please adjust by hand.check photo:7.Finish welding:turn the walking handrail to the right ,machine stop walk,then turn off the yellow button(temperature knob),but before cut off the power,please wait until actual temperature below 50 ℃,then we can cut of the main power,or it would be damage heat system.8. Don’t use it in rainy day,the workplace should be dry, flat and safety of fire.The machine should have technical person to operate, it is forbid that someone use it without specific knowledge. Working voltage：110V—220V. Strictly prohibited without permission disassemble,you should be responsible the result yourself.Please pay attention:In order to keep heat element,we add Automatic Dormancy function,it means if not using welder over 10 minutes,machine would be enter dormancy state.if want it reback to work,just press the 'Reset’ button or put the operation handle to right is ok,but it needs 1 minute to raise the temperature,so we need to wait.Tips:For first user,we can use waste banner to test and find proper temperature,we can do like this:take a small banner close the nozzle,if the banner hot melt quickly,it means,the temperature is OK,it not strong or burnt,we can increase or reduce temperature.we can also write down the temperature for this thickness of banner as sample.in next welding,based on this temperature.we just need to increase or reduce the temperature depends on thickness of banners.check the welding result:Plugboard must be grounded wire,when using welding machineYou mustn’t turn off the machine until the welding machine will completely cool down in a few minutes. Then pull out the plug.Preparation before using the machine1. You should adjust the temperature and speed according to the thickness of banners.2. Fix the cloth on the smooth ground to make sure the best result.Maintain1. Clean the nozzle with copper brush.2. Clean the air inlet with soft bristle brush.3. Check the power cord and plugs to avoid any mechanical damage.Phone: , , : Sunny Tsao, Digital is one of the leading and credible suppliers of hot air welding machine. Top quality, easy operation, reliable performance and good after-sales service are our advantages. Welcome to wholesale quality hot air welding machine from our factory which can also offer customized service.
Другие товары поставщика
|
|
|
SINOTEC DIGITAL CO., LTDPhone:,Website:,, ,
water based printer E180 E320Product feature:*The printing quality is co... |
|
|
|
SINOTEC DIGITAL CO., LTDPhone:,Website:,, ,
UV Flat Bed PrinterEquipped with imported UV LED lamp, energy saving, environmental protection an... |
|
|
|
Sinotec Digital is one of the leading and credible suppliers of sk4 ink. Top quality, easy operation, reliable performance and good after-sales se... |
|
|
|
Sinotec Digital is one of the leading and credible suppliers of manual grommet machine. Top quality, easy operation, reliable performance and good... |
|
|
|
SINOTEC DIGITAL CO., LTDPhone: ,,,
machine is start manufacture at 2002, It is widely used in Organic glass, acrylic, crystal words polishing... |
Все товары поставщика
Похожие товары
