Cone Calorimeter / Cone calorimetric test equipment

The Cone Calorimeter is widely used to evaluate fire performance of materials and products under controlled heat-flux exposure. It provides accurate characterization of heat release, smoke generation, ignition properties, toxic gas production, and combustion behavior.

Common applications include building materials, foams, plastics, composites, textiles, cable insulation, transportation materials (railway, maritime, automotive interiors), aerospace composites, polymer research, and fire-retardant development.

Its measurement data is essential for predicting fire hazards, conducting flame-retardant assessments, verifying regulatory compliance, and supporting fire-safety engineering analysis.

Standards

The system complies with major international fire-reaction standards, including:

ASTM E1354 – Heat and Visible Smoke Release Rates

ISO 5660-1 – Heat release, smoke production, and mass loss rate

ASTM E1474 – Flame spread evaluation

ASTM F1550 – Flame spread of plastics in furniture

ASTM E1740 – Large-panel cone calorimeter testing

ASTM D6113 – Fire performance of materials

IMO MSC 40(64) – Marine fire test procedures

BS 476-15 – Fire tests for building materials

NFPA 264 / NFPA 271 – Fire and smoke measurement standards

ULC-S135-04 – Canadian fire test standard

CSN EN 45545-2+A1 – Railway vehicle fire protection

CSN EN 13501-1+A1 – Classification of building products

Features

Ignition System

10 kV spark igniter with fire-off safety system; position automatically detected via mechanical linkage.

Fully automated ignition, timing, gas control, and flame-off functions.

Exhaust System

Stainless-steel design including hood, pipes, diffusion plate, orifice flow meter, and axial-flow fan.

Long-life stainless-steel smoke collection cover, sampling needle, and exhaust fan.

Gas Sampling System

Ring sampler with 12 evenly distributed pores opposite airflow direction.

Three-stage 0.5 μm precision filtration with particle filter, CO₂ filter, and water trap.

Refrigerated cold trap with 0–5 °C temperature control.

Dust filter installed 685 mm from smoke-collecting hood.

Measuring System

Paramagnetic O₂ analyzer (0–25%), Servomex sensor with linear response.

Laser system for smoke-density measurement.

High-precision load cell for dynamic mass-loss monitoring.

PID temperature control with three thermocouples for cone-heater measurement.

User Operating System

LabVIEW-based professional control platform; intuitive and user-friendly.

PID temperature controller integrated with programmable control module.

PLC-based acquisition and airflow regulation; automatic sample ID management and database recordkeeping.

Technical Parameters

Item	Parameter	Value
Power supply	–	208–230 V, 50/60 Hz, 50 A, single phase
Cone heater	–	5000 W Inconel heater, 0–120 kW/m²
Sample size	–	100 mm × 100 mm × ≤50 mm
Ignition	–	10 kV automatic spark igniter
Temperature control	–	PID, 3× K-type thermocouples
Exhaust system	–	Stainless-steel hood, duct, orifice meter, axial fan
Gas sampling	–	12-pore ring sampler, 0.5 µm triple filtration, 0–5 °C cold trap
Gas analyzers	–	O₂ paramagnetic (0–25%); CO₂ NDIR (0–10%); CO NDIR (0–1%)
Smoke measurement	–	He-Ne laser photometric system
Load measurement	–	Sartorius load cell, 0.01 g resolution
Data acquisition	–	16-bit A/D, 4 scans/sec
Control system	–	LabVIEW + PLC, touchscreen control
Data output	–	Excel reports, customizable formats
System configuration	–	19" rack modules; customizable full-system layout

Другие товары поставщика

	Xenon Arc Chamber	1. According to different specimens, xenon aging test chamber has a variety of models to choose from; For flat specimens, rotating drum type xenon ...
	Thermal Radiation Performance Tester(RPP)	The RPP test is mainly used to determine the radiant thermal protection performance of thermal protective clothing. Since thermal radiation is on...
	Fabric Formaldehyde Content Tester	ASTM D600 Formaldehyde Climate TesterIntroductionIn China, the national mandatory standard "national textile products basic safety technical specif...
	Fabric Cooling Sensation Tester	Applications Fabric Cooling Sensation Tester is used to evaluate the instant cooling sensation upon skin contact for textiles and sheet materials,...
	Large-Scale Composite Salt Spray Test Chamber	TheLarge-Scale Composite Salt Spray Test Chamberis a professional environmental simulation instrument designed to replicate complex corrosion condi...

Все товары поставщика

Похожие товары

	Air Intake Filter Test System	Продавец: Standard Groups	The Air Intake Filter Test System is designed for testing industrial air filters and engine air f...
	Mattress Spring Fatigue Tester，ASTM D3574 ，how to test mattress for sagging	Продавец: Standard International Group (HK) Limited	The King Size Foam Fatigue Tester is a single-station pneumatic fatigue testing system designed f...
	Mattress Rollator，ASTM F1566 ，Mattress Durability Tester，Mattress Fatigue Tester	Продавец: Standard International Group (HK) Limited	The Mattress Rollator is a laboratory durability testing system designed to evaluate the long-ter...
	HD2 Pneumatic Foam Fatigue Tester，ISO 3385，Foam Fatigue Testing Machine	Продавец: Standard International Group (HK) Limited	The HD2 Pneumatic Foam Fatigue Tester is a heavy-duty, single-station laboratory testing machine ...
	VW Heel Abrasion Tester，ISO 4649 ，Heel Performance Testing Machine	Продавец: Standard International Group (HK) Limited	The VW Heel Abrasion Tester is designed to evaluate the wear resistance of floor covering materia...