OSU Heat Release Rate Test Device for Building Materials
Whats/App: +86 156 1874 6768
Web: standard-groups.com
Standards
The apparatus supports compliance with the following standards:
BSS 7322 – Aerospace materials flame spread, smoke density, and toxicity evaluation.
AITM 2.0006 – Aerospace materials flame spread and smoke generation measurement.
FAR Part 25 Appendix F Part IV – Aircraft cabin material flame spread and smoke toxicity requirements.
GB/T 27904‑2011 – Flame spread performance of interior decoration materials (can be combined with HRR testing).
GB 8624‑2012 – Classification of combustion performance of building materials and products (can be combined with HRR results).
Parameters
| Parameter Category | Details |
|---|---|
| Dimensions | 760 mm (W) × 1850 mm (H) × 850 mm (D) |
| Weight | 218 kg |
| Combustion Chamber | Stainless steel with high-temperature glass viewing window |
| Heat Radiation Source | 4 Glowbar heating rods, up to 35 kW/m² flux |
| Temperature Control | 2 independent PID controllers |
| Power Supply | 220 V, 35 A |
| Operating Temperature | 10°C – 35°C |
| Combustion Gas | Methane |
| Auxiliary Gas | Constant temperature and flow air supply |
Features
Stainless-steel combustion chamber with high-temperature observation window.
Four Glowbar heating rods providing up to 35 kW/m² radiant heat flux.
Dual PID temperature controllers for precise heat regulation.
Fully automatic pneumatic sample feeding and shielded door system.
Upper stationary burner and movable lower burner for flexible testing.
Rotor flow meters for controlling upper and lower burner gas flow.
Movable T-shaped calibration burner and flow controller for system calibration.
Mass flow controllers automatically applied to thermopile calibration.
Water-cooled heat flux sensors for accurate measurement of irradiated heat.
Airflow temperature control system for constant temperature and flow within the test chamber.
Orifice flow meters to monitor flow rate and pressure entering the test chamber.
Integrated data acquisition system and standard HRR testing software.
Accessories
Water-cooled heat flux sensors
Pneumatic sample feeder and shielded door
Upper and lower burners with flow control
T-shaped calibration burner
Rotor and mass flow controllers
PID temperature controllers
Data acquisition hardware and HRR software
Test Procedures
Ensure installation space allows safe operation and access.
Connect the apparatus to a 220 V, 35 A power supply.
Provide constant-temperature, constant-flow auxiliary gas.
Connect methane as the combustion gas supply.
Mount the test sample in the combustion chamber.
Adjust Glowbar heating rods and set PID controllers to desired heat flux.
Activate the automatic sample feeder and shielded door system.
Ignite the sample and upper/lower burners.
Monitor heat release rate, temperature, and gas flow using the software interface.
Record data for HRR, flame spread, and smoke generation.
After testing, shut off gas supply and allow the chamber to cool before sample removal.
Maintenance Information
Inspect and clean the combustion chamber and viewing window regularly.
Check burners, gas lines, and flow meters before each test for leaks or blockage.
Calibrate heat flux sensors and PID controllers periodically to ensure accuracy.
Verify data acquisition system and HRR software functionality.
Replace worn or damaged safety interlocks and pneumatic components as needed.
Отправить запрос, связаться с поставщиком
Другие товары поставщика
 |
Resistance to flame propagation tester,ECE R118 Annex 10 | Whats/App: +86 156 1874 6768 Web: standard-groups.com Introduction This equipment is designed and manufactured according to ECE R118 Annex 10. T... |
 |
Coatings Shear Fatigue Test device | Whats/App: +86 156 1874 6768 Web: standard-groups.com Standard YY/T 0988.13-2017 (China): Specifies shear fatigue testing protocols for coatings... |
 |
Advanced catheter power injection flow and pressure tester equipment | Whats/App: +86 156 1874 6768 Web: standard-groups.com Applications The catheter flow and pressure tester for power injection is an important med... |
 |
Contact Lens Luminous Transmittance Analyzer | Whats/App: +86 156 1874 6768 Web: standard-groups.com The Contact Lens Luminous Transmittance Analyzer is a precision instrument designed to meas... |
 |
Tabletop xenon arc weathering tester for laboratory | Get a quote： Whats/App: +86 156 1874 6768 Web: standard-groups.com The Water-Cooled Xenon Lamp Weathering Test Chamber is a premium environmenta... |
Похожие товары
 |
Высокоскоростная экструзионная линия для производства гофрированных труб с двойными стенками из ПЭВП с водяным охлаждением | Продавец: Shandong HUASU Plastic Technology Co.,Ltd. | Формы имеют структуру с двойным каналом потока и фильерную головку, обработанную азотированием и ... |
 |
PanEVAP & MVR system | Продавец: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd | A multiple-effect evaporator is a device that efficiently uses steam heat to evaporate water. Wat... |
 |
PanGAP wide gap welded plate heat exchanger | Продавец: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd | PanGAP wide gap welded plate heat exchangerconsists of a welded plate pack with different channel... |
 |
PanBloc welded plate heat exchanger | Продавец: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd | PanBloc welded plate heat exchangeris compact and efficient, although fully welded, is totally ac... |
 |
PanBox welded plate heat exchanger | Продавец: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd | PanBox welded plate heat exchangerconsists of a laser welded plate pack with optimized corrugated... |
