Laboratory Burner for Insulation Fire Performance
Whats/App: +86 156 1874 6768
Web: standard-groups.com
Standards
The system is compatible with the following international aerospace fire testing standards:
BSS 7387 – Flame spread and combustion behavior of aerospace materials
AITM 2.0056 – Heat release rate measurement of aerospace materials using cone calorimeter
FAR Part 25 Appendix F Part VII – Heat release and fire performance requirements for aircraft cabin materials
Parameters
| Item | Specification |
|---|---|
| Overall dimensions | 1500 mm (W) × 1800 mm (H) × 900 mm |
| System weight | 150 kg |
| Power requirement | 220 V, 10 A |
| Operating temperature | 10°C to 35°C |
| Fuel type | Aviation kerosene |
| Air supply | Minimum 120 PSI compressed air |
| Flame temperature capability | ≥ 2000 ± 50 ℉ |
| Heat flux output | ≥ 10.6 W/cm² |
| Temperature control bath | ≥ 2 × 0.14 m³ |
Features
Incorporates the FAA-approved NexGen aviation fuel burner, developed to replace discontinued legacy burners (Park DPL 3400. Lennox OB-32. Carlin 200 CRD).
Retains the operational principles of previous burner generations while enabling more precise measurement of fuel and air test parameters.
Modular architecture facilitates future FAA upgrades without full system replacement.
The burner cone is fabricated from corrosion-resistant and high-temperature alloy to ensure durability in severe thermal conditions.
The NexGen burner includes key components such as baffle, fuel nozzle, igniter, fuel rail, mounting plates, ventilation duct, housing, muffler, and acoustic resistance unit.
Equipped with fuel pressure gauge, fuel solenoid valve, fuel temperature sensor, air pressure regulator, and air temperature sensor for stable control.
A temperature-controlled ice bath system (≥ 2 × 0.14 m³) allows regulation of fuel temperature prior to combustion.
Flame characteristics can be adjusted by modifying fuel nozzle configuration and air pressure input to meet different standard requirements.
The burner is covered with a thermal insulation blanket to protect fuel lines and the burner body.
Capable of delivering flame temperature of at least 2000 ± 50 ℉ and heat flux of at least 10.6 W/cm².
Mounted on a heavy-duty steel frame that supports both horizontal and vertical specimen installation.
Calibration utilizes a thermocouple comb composed of seven grounded K-type thermocouples (1.6 mm diameter, ceramic-insulated, metal-sheathed, 30 AWG wire), fixed on an angle bracket for standardized placement on the specimen frame.
Includes a radiant heat flux sensor with cooling system, installed on a fixed support bracket for reliable measurement.
Accessories
The system is supplied with the following components:
NexGen aviation fuel burner
Flame penetration test fixture for thermal and acoustic insulation
Dynamic loading motion system
Fuel temperature control ice bath
Thermocouple calibration comb
Radiant heat flux sensor with cooling unit
Heavy-duty specimen mounting frame
Burner thermal insulation blanket
Test Procedures
Mount the test specimen on the horizontal or vertical frame according to the selected standard.
Connect aviation kerosene supply and compressed air (≥120 PSI).
Set and stabilize fuel temperature using the ice bath system.
Adjust air pressure and fuel flow parameters per test requirements.
Ignite the NexGen burner and allow the flame to stabilize.
Position the flame relative to the specimen and initiate exposure.
Monitor flame temperature and heat flux using thermocouples and sensors.
Observe whether flame penetrates the insulation material within the specified time.
Record data and evaluate performance in accordance with the applicable standard.
Maintenance Information
To ensure long-term reliability and compliance:
Clean the fuel nozzle regularly to prevent blockage.
Inspect fuel lines and valves for leakage before each test.
Calibrate thermocouples and heat flux sensors periodically.
Replace the burner insulation blanket if damaged or degraded.
Maintain proper ventilation in the test area.
Keep the compressed air system dry and free from oil contamination.
Отправить запрос, связаться с поставщиком
Другие товары поставщика
 |
Advanced Salt Spray Corrosion Test System ASTM B117 Laboratory Use | Get a quote： Whats/App: +86 156 1874 6768 Web: standard-groups.com Standards (1)ASTM B117. ASTM G85. ASTM D1141-98 (2)DIN EN ISO 9227 (NSS, ES... |
 |
Photovoltaic module insulation resistance tester | Whats/App: +86 156 1874 6768 Web: standard-groups.com The Photovoltaic Module Insulation Resistance Tester is a precision instrument designed for... |
 |
Cantilever Beam Fabric Stiffness Tester ASTM D1388 Industrial Supply | Get a quote： Whats/App: +86 156 1874 6768 Web: standard-groups.com Features (1) Infrared “stealth” detection system: replaces tradi... |
 |
Sponge foam collapsible hardness tester | Whats/App: +86 156 1874 6768 Web: standard-groups.com This machine is used to measure the indentation hardness of porous elastic materials. The p... |
 |
Conveyor Belt Drum Friction Testing Machine | Whats/App: +86 156 1874 6768 Web: standard-groups.com Main Purposes of Conveyor Belt Drum Friction Testing Machine The conveyor belt drum fricti... |
