NES 713 High-Precision Smoke Toxicity Test Chamber

Whats/App: +86 156 1874 6768

Web: standard-groups.com

Standards

The equipment is designed and manufactured in compliance with the following standard:

NES 713 – Determination of the Toxicity Index of the Products of Combustion from Small Specimens of Materials

Parameters

Parameter	Specification
Flame height	100–125 mm (blue flame)
Maximum hot spot temperature	1150 ± 25 °C
Number of sampling ports	12
Exhaust capacity	≥ 50 L/s
Gas supply	Compressed air, methane or natural gas
Power supply	AC 220 V, 50/60 Hz, 5 A
Equipment weight	Approx. 150 kg
Overall dimensions	1.185 (W) × 700 (D) × 2.100 (H) mm

Features

Rigid steel chamber with reinforced frame construction to ensure long-term structural stability

Large observation window with dark-coated inner walls to clearly observe the combustion behavior of specimens

Inner chamber walls treated with PTFE coating to reduce chemical corrosion caused by combustion gases

Built-in stirring fan to ensure uniform distribution of smoke and combustion gases inside the chamber

Top-mounted exhaust fan with stainless steel exhaust duct, automatically activated after test completion to discharge residual smoke

Integrated industrial design with panel-mounted structure, providing intuitive operation and ergonomic human–machine interface

High-voltage pulse automatic ignition system offering stable ignition performance and enhanced operational safety

Imported K-type thermocouples for accurate and reliable temperature measurement

Adjustable stainless steel specimen mesh tray allowing precise positioning relative to the flame

Imported precision rotameters for accurate control of gas and air flow rates

Branded pressure gauges, pressure regulators, and solenoid valves to control gas pressure and on/off status, ensuring safe operation

PLC and touchscreen control system enabling automatic control, detection, calculation, and data storage

Automatic waste exhaust mode to remove smoke upon test completion according to preset program logic

Manual and automatic test modes selectable to suit different testing requirements

Accessories

(1) Stainless steel adjustable specimen mesh tray

(2) K-type thermocouples

(3) Precision rotameters for gas and air control

(4) Pressure gauge and pressure regulating valve

(5) Stainless steel exhaust duct

(6) PLC controller with touchscreen interface

Test Procedures

1. Pre-Test Preparation

Environment confirmation:

The test area should be an independent, well-ventilated space, kept away from flammable materials and densely populated areas. The floor must be dry and free of standing water. The power supply should be properly grounded and meet AC 220 V, 50/60 Hz, 5 A requirements.

Equipment inspection:

Check all gas pipelines (methane or natural gas) for leakage and confirm the gas cylinder pressure is within 0.2–0.3 MPa. Verify that the exhaust fan and stainless steel exhaust duct are unobstructed and capable of providing an exhaust capacity of at least 50 L/s. Confirm normal operation of the K-type thermocouples, rotameters, and PLC touchscreen with no alarm indications. Ensure proper door sealing, intact polycarbonate observation window, and undamaged PTFE inner wall coating.

Safety protection:

Operators should wear high-temperature resistant gloves, safety goggles, gas masks equipped for CO and HCN protection, and safety shoes. A portable multi-gas detector (monitoring O₂, CO, HCN, NOₓ) and an emergency eyewash station should be available on site.

2. Specimen Installation

Specimens should conform to NES 713 requirements, typically measuring 100 mm × 100 mm with a thickness not exceeding 10 mm. Cable materials may be fixed using a coiled arrangement. No more than three specimens should be tested in a single run, evenly distributed on the stainless steel mesh tray to avoid flame obstruction. Adjust the tray position so that it is located directly above the burner, with a distance of 100–125 mm from the burner nozzle to ensure full flame coverage on the specimen underside.

3. Ignition and Test Execution

Close the chamber door and confirm the locking mechanism is engaged. Select “Automatic Mode” on the control screen and start the test. The system will automatically perform high-voltage pulse ignition for approximately three seconds, followed by flame stability detection. If a stable flame is not detected within five seconds, re-ignition will be attempted automatically, up to three times. The combustion process typically lasts 10–15 minutes, during which the internal fan continuously mixes smoke to maintain uniform concentration.

4. Gas Sampling

Gas sampling begins at the fifth minute after ignition and continues until the end of combustion. Twelve dedicated sampling ports are used to connect gas detector tubes (for gases such as HCN, CO, and HCl) or online gas analyzers. Each sampling port is equipped with an independent flow meter, with the sampling flow rate controlled at no more than 1 L/min to avoid negative pressure interference. After sampling, tubes are sealed immediately, labeled with time and port number, and sent for quantitative laboratory analysis.

Maintenance Information

Regularly inspect gas pipelines, solenoid valves, and pressure regulators to ensure leak-free operation. Clean the specimen tray and inner chamber surfaces after each test to prevent residue accumulation. Periodically check the condition of the PTFE inner wall coating and replace or repair it if damage is observed. Verify calibration status of thermocouples and rotameters according to laboratory quality requirements. Ensure the exhaust system and stirring fan remain unobstructed and operate smoothly.

Conclusion

The NES 713 Navy Engineering Smoke Toxicity Test Chamber provides a reliable and standardized solution for assessing the toxicity of combustion products from materials used in high-risk fire environments. With precise flame control, uniform smoke mixing, multi-point gas sampling, and automated control functions, the system ensures accurate evaluation of smoke toxicity indices in strict accordance with NES 713 requirements, supporting safety-critical material selection and certification.

Другие товары поставщика

	Accelerated Weather Tester(Xenon)	Features and Benefits 1.Equipped with high-pressure xenon lamps, accurately reproduce the full spectrum of natural sunlight, including ultraviolet...
	Automatic voltage internal resistance tester	The Automatic Voltage & Internal Resistance Tester is a precision electrical testing instrument designed for rapid and accurate measurement of ...
	Combustion Test Manikin	Whats/App: +86 156 1874 6768 Web: standard-groups.com Application The Burning Manikin System is primarily applied in the following areas: Fire ...
	Strength Tester for Lead - end of Photovoltaic Modules	Standard IEC 61215-2:2016: Terrestrial Photovoltaic (PV) Modules – Test Requirements for Electrical and Mechanical Components CE Certificat...
	Coating thickness gauge/film thickness gauge	Standard Coating Thickness Gauge complies with international standards includingASTM B499,ASTM D1400,ISO 2178,ISO 2360, andGB/T 4956, ensuring rel...

Все товары поставщика

Похожие товары

	ISO 29463 HEPA/ULPA filter performance testing System	Продавец: Standard International Group (HK) Limited	Whats/App: +86 156 1874 6768 Web: standard-groups.com Standards The system supports and compli...
	High-Precision ISO 16890 Filter Media Test Rig for R&D and QC	Продавец: Standard International Group (HK) Limited	Whats/App: +86 156 1874 6768 Web: standard-groups.com Standards The system can execute and com...
	Mobile Floor Scrubber Aging Life Tester IEC 60312	Продавец: Standard Groups	Get a quote： Whats/App: +86 185 0176 3615 Web: qinsun-lab.com TheMobile Floor Scrubber Aging L...
	ISO 12103 Cleanable Filter Media Test System	Продавец: Standard International Group (HK) Limited	Whats/App: +86 156 1874 6768 Web: standard-groups.com Standards The system complies with: (1)...
	Robotic Vacuum Cleaners Edge-Following Tester	Продавец: Standard Groups	Get a quote： Whats/App: +86 185 0176 3615 Web: qinsun-lab.com TheEdge-Following Test Equipment...