Pre-Deformation Mold

Pre Deformation Mold

When the plastic material rushes into the mold cavity, it loses heat due to heat conduction, and the melted plastic will freeze and solidify, therefore, for complex or large products, high mold temperature is usually used for filling, the purpose is to reduce the injection molding conditions, the stress is also conducive to debugging product deformation and shrinkage. However, high mold temperature will produce excessive oil stains, and molds with poor precision are prone to burrs.

PRE-DEFORMATION MOLD TYPES

Automotive Window Frame Mould

USM has 15 years of experience in pre-deformed mold designing, From the mold flow analysis to get theoretical deformation amount, and then make Crim's test by UDB material file which used to obtain the actual deformation amount, then leave enough space for steel when mold design according to professional experience in order to shorten the modification time and longer mold life.

Water Tank Mould

The mold will be made welding process many times during modification, but it will reduce the accuracy and mold life a lot. some factories might use the normal steel to make manufacturing and then make real mold manufacturing after the first prototype mold work well, but it also influences the mold cost and delivery time.

Air Chamber Mold

With over 15 years of pre-deformed mold, USM Mold has mastered scientific and complete pre-deformation mold technology, from project management, mold flow analysis, design, manufacturing, assembling, mold trial, and final measurement.

PA66 GF30 Car Parts Plastic Injection Mold

Pre-deformation means that the product will be designed mold in opposite direction in advance. The product is injected and cooled by natural shrinkage, the two deformations will be offset to obtain a product and meet the drafting tolerance.

Car Door Mold

The product is an assembly functional part with very high requirements for size and installation location, and it is an external part, there are very strict requirements on the clearance and tolerance after installation;

Automotive Fan Mould

The common products used to be water chambers, air chambers, engine inlet valve pipe and nylon connectors, and automotive AC systems: fan covers, fans, automotive brackets, sunroofs, mirror triangle brackets, automotive bottom sheets, and so on.

More

The main reasons to cause the plastic parts are warpage and deformation

Usually, the main part of the product is thicker and the ribs are thin, when the plastic parts are cooled, there are still uncondensed parts in the middle of the main body after the ribs are completely cooled, the continued cooling of the main body will inevitably cause the plastic parts to deform in the opposite direction to the ribs.

The influence of insert injection moldingprocess parameters on deformation

When the temperature of the mold cavity and core side is very different, it will cause the mold to freeze and not open, the higher the mold temperature, the bigger the shrinkage and the greater the deformation, the temperature difference between the inner and outer surfaces of the product will cause thermal stress and thermal deformation, and the inconsistent temperature of different areas of the mold will cause uneven shrinkage of the product and warp deformation.

Low melt temperature is not conducive to injection molding, the decrease in melt viscosity will increase the cooling rate of the melt, lead to poor plasticization of the melt and increase the difficulty of the process; high melt temperature is good for molding, which can reduce the viscosity of the melt and reduce the orientation stress, but it cannot too high which will cause thermal degradation.

Injection pressure is to overcome the existence of resistance, in injection molding, the appropriate injection pressure should be suitable, and the standard is the filling will be the same after the speed is added. High injection pressure will influence the stress pressure for melt plastic during injection, so the smaller injection pressure is, the better for protecting the mold and equipment, but if it is too small which will cause unfull filling.

The holding time has a big effect on the size and elastic deformation of the product, when the melt is injected from the screw into the mold cavity, it will contract cold, the function of holding pressure is to make up for the space left by the injection.

The holding time is to ensure that there are no quality issues such as shrinkage marks on the part surface and reduce the holding pressure as much as possible, excessive holding pressure will increase the internal stress caused by the solution on the mold cavity and the product.

Excessive holding pressure causes excessive internal stress of the product, resulting in product stress cracking and burrs, too small holding pressure will cause product shrinkage, and the holding pressure controls the amount of material fed.

It has a big effect on the shrinkage and deformation of the product, mainly to make up for the remaining mold cavity space during injection filling.

Multi-stage injection speed should be used: slow-fast-slow, the injection speed is fast, the heat of the melt can be maintained, the viscosity will be reduced, and it can flow farther, but if the injection speed is too fast, the gas in the column cavity will not be discharged.

In the case of normal process parameters, the injection position is filled to 90% of the product and then transferred to holding pressure, it is not unrelated to the shrinkage of the product and the warpage deformation, under unusual circumstances, it may be due to improper parameter adjustment, too much material causes warping and deformation.

The cooling time is insufficient, when the product is demolded, the thrust generated by the ejector pin acts on the surface that is not cold-solidified, which causes the product to deform. If the cooling time is too long, the hot melt is injected into the cold mold cavity, and the melt shrinks and wraps the mold core when cold, resulting in an increase in the demolding force.

If you want to know more about china mold maker, please contact us.

Другие товары поставщика

	Medical TPE Mold	Medical TPE Mold Design is the source of a high-quality mold, one good mold design will be half success, USM uses the world's leading software to ...
	Transparent PC Injection Mold	It is the most widely used thermocouple in the hot runner system, and it is characterized by low price and is suitable for vacuum oxidation in redu...
	Plastic Pipe Mold	Plastic Pipe Mold The gas-assisted controller is used to control the pressure of nitrogen to the mold at different times, the controller is divi...
	Cold Runner & Hot Runner Plastic Mold	Generally, the temperature-sensitive wire is composed of steel wire insulated with a heat-sensitive material, the temperature sensing wire is commo...
	Pre-Deformation Mold	Pre Deformation Mold When the plastic material rushes into the mold cavity, it loses heat due to heat conduction, and the melted plastic will free...

Все товары поставщика

Похожие товары

	steel moulds for precast concrete	Продавец: Sino Mould (Hubei) Co.,Ltd	steel moulds for precast concrete What Are Steel Moulds & Their Role for precast concre...
	new jersey barrier moulds	Продавец: Sino Mould (Hubei) Co.,Ltd	new jersey barrier moulds Barrier Types & Custom Configurations Single-sided parapet bl...
	culvert moulds	Продавец: Sino Mould (Hubei) Co.,Ltd	culvert moulds Structural & Configuration Types By Mold Configuration: Horizontal-type ...
	manhole forming systems	Продавец: Sino Mould (Hubei) Co.,Ltd	manhole forming systems Precast Manhole/ Inlet Molds , Also called Molds for Inspection Cha...
	precast concrete molds	Продавец: Sino Mould (Hubei) Co.,Ltd	precast concrete molds About Sino Mould Sino Mould is a precast concrete mould manufacturer...