spray water repellency tester

• 

Water Repellency Tester is used to check the water repellency of the fabric by spray test in textile testing laboratory. Suitable for Table cloth, tapestry, flooring material fabric manufacturer or processors.Water repellency test method is applicable to any textile fabric, which may or may not have been given a water-repellent finish. It is very necessary for a manufacturer to test the water repellency ability of the fabric. This method is especially suited for measuring the water-repellent efficacy of finishes applied to fabrics.The water repellency ability of the fabric is tested with spray test. The Evaluation of the test is visual appreciation of the surface of the fabric (number of absorption points on the surface). It is very important to test the repellency of a garment worn in foul weather conditions. The more the repellency more comfortable the fabric will be during use. The repellency tends to decrease during washing, so a re-impregnation of a water repellent product is advised.

Testing Standards:
ISO 4920, BS EN 24920, BS 3702, GB/T 4745, AATCC 22, M&S P23, NEXT 23

Applications:
Spray Rating Tester is used to determine the surface wetting resistance of fabrics.

Product Information:
The Spray Tester comprises a metal framework allowing distilled water to be sprayed through a nozzle onto a test specimen at 45° and 150mm below. The appearance of the specimen is compared against an optional photographic scale to rate.

Instrument features:
1. The instrument structure is simple, mainly by the main frame, funnel, nozzle, sample holder and sample holder;
2. Nozzle have a total of 19 aperture evenly distributed, the aperture required by the standard custom. 250ml of water poured into the funnel can flow out of the nozzle within 25-30s;
3. The racks on the upper edge of the racks are at a 45 ° angle to the horizontal;
4. The center of the upper edge of the sample holder ring, ie the distance from the center of the sample to the nozzle, is 150 mm.

Technical Parameters:
1. Structure: stainless steel;
2. Surface treatment: painting;
3. Dimensions: 230 × 250 × 500mm (length × width × height);
4. Weight: 5kg (11lb).

Attachment:
Nozzle and rubber hood;
water tray;
AATCC (22) Ratings Standard Chart Cards

Другие товары поставщика

	Medical Face Mask Air Exchange Pressure Difference Tester	Products meet the standard requirements, which is YY0469-2004 "Medical surgical mask technical requirements" and YY 0969-2013 "Disposable medical m...
	Carpet Flammability Tester	Standards:BS 4790, ISO 6925, BS 6307Applications:The Flammability Tester is used to test the effects of a small source of ignition on floor coverin...
	AATCC Viewing Board	Standards:American Association of Textile Chemists and Colorist (AATCC) approved test methods 88B/88C/124/128/143/178.Product Information:1. Utilis...
	Dry Wet rubbing fastness Tester	Testing Standards:ASTM F1319, AATCC 8/165, BS 1006 D02, GB/T 3920, ISO 105 D02/X12, JIS L0849, M&S C8/C8A, NEXT TM6Applications:Electronic Croc...
	Fabric Negative-ion Concentration Tester	The negative ion generation tester is mainly used to detect the negative ion generation of textiles, and evaluate the negative ion generation capac...

Похожие товары

	Air Permeability Tester STD- F8	Продавец: Standard International Group (HK) Limited	The Air Permeability Tester is designed to quickly and accurately measure the breathability and p...
	Surface Performance Tester STD-FB4 - A	Продавец: Standard International Group (HK) Limited	Introduction TheSurface Tester analyzes finger movements-particularly, strokes-performed by arti...
	Compression Tester STD - FB3 - A	Продавец: Standard International Group (HK) Limited	TheCompression Tester analyzes hand movements-particularly, pushing with a finger-performed by ar...
	Single - Strand Bending Tester STD - FB2 - SH	Продавец: Standard International Group (HK) Limited	Standards ASTM A370. ASTM A416. ISO6934.4 The Single Fiber Bending Tester makes it possible to ...
	Bending Tester STD- FB2 - S	Продавец: Standard International Group (HK) Limited	Compliance Standards ASTM D790 (Plastics Flexural Properties) ISO 178 (Flexural Strength of Rig...