Rubber hose outer coating wear testing machine
Product Introduction:
Rubber hose outer coating Wear testing machine for hydraulic hoses and other similar types of hoses with fabric or steel wire reinforced outer coating with a smooth and flat surface.
Test method:
1. Install the assembled sample and mandrel on the test device, and ensure that the sample has no axial movement and （or） rotation.
2, place the abrasive tool to make contact with the sample, apply the vertical static pressure F specified in the product standard, and start the machine. If the force F is not specified in the product standard, the applied vertical static pressure should be 50N±0.5N.
3, the test is carried out until the specified number of cycles is completed, and then the sample assembly is removed from the test device, and the sample with or without a core shaft is weighed again as the initial weighing. It is important to remove any particles attached to the outer coating before weighing.
Test standard:
GB/T 12721-2007 - Determination of abrasion resistance of rubber hose outer coating
ISO 6945:1991 - Determination of the abrasion resistance of rubber hose cladding
KS M ISO 6945-2013 - Determination of the abrasion resistance of the outer coating of rubber hoses
EN ISO 6945-1996 - Determination of the abrasion resistance of rubber hose outer coatings
DS/ISO 6945-1984 Determination of wear resistance of rubber hose cladding
Main parameters:
1, reciprocating frequency: 1.25Hz（45 RPM）
2, cycle stroke: 200mm
3, loading static pressure: 50N±0.5N（other pressure weights can be customized processing）
4. Mandrel length: 150mm
5, shaft diameter: 5mm, 8mm, 10mm, 13mm, 16mm, 19mm, 22mm, 25mm, 32mm, 38mm, 45mm, 51mm, optional three, can also provide dimensional processing
Отправить запрос, связаться с поставщиком
Другие товары поставщика
 |
Thin Film Pendulum Impact Tester | Main Uses of the Film Pendulum Impact Tester The film pendulum impact tester is mainly used to determine the resistance to pendulum impact of mate... |
 |
Paper quantitative tester | Product Introduction: The circular square quantitative sampler （referred to as quantitative sampler） is a special sampler for the quantitative det... |
 |
Rubber non-rotor vulcanization Tester | Product Introduction: Non-rotor vulcanizer is a rubber processing industry control rubber material quality, rapid inspection and rubber basic rese... |
 |
Diaper leakage tester | Main uses: Nonwovens liquid loss measurement instrument is mainly used to measure the amount of liquid loss in nonwovens material and evaluate its... |
 |
Nasal Oxygen Cannula meter | Introduction The Nasal Oxygen Tube Tester plays a crucial role in the medical field. The following is a detailed introduction to its main uses, co... |
Похожие товары
 |
Air Permeability Tester STD- F8 | Продавец: Standard International Group (HK) Limited | The Air Permeability Tester is designed to quickly and accurately measure the breathability and p... |
 |
Surface Performance Tester STD-FB4 - A | Продавец: Standard International Group (HK) Limited | Introduction TheSurface Tester analyzes finger movements-particularly, strokes-performed by arti... |
 |
Compression Tester STD - FB3 - A | Продавец: Standard International Group (HK) Limited | TheCompression Tester analyzes hand movements-particularly, pushing with a finger-performed by ar... |
 |
Single - Strand Bending Tester STD - FB2 - SH | Продавец: Standard International Group (HK) Limited | Standards ASTM A370. ASTM A416. ISO6934.4 The Single Fiber Bending Tester makes it possible to ... |
 |
Bending Tester STD- FB2 - S | Продавец: Standard International Group (HK) Limited | Compliance Standards ASTM D790 (Plastics Flexural Properties) ISO 178 (Flexural Strength of Rig... |
