Fabric Fiber Shedding Degree Tester (Friction)-QINSUN
Instrument Testing Principle
Lay the specimen flat and fix it on the holder. Make the wet abrasive attached to the friction head perform reciprocating friction movements on the specimen under the specified load for a specified number of times with a certain stroke. Then compare it with the standard sample and visually rate the degree of fibers adhered to the abrasive to characterize the degree of fiber shedding of the specimen. It is suitable for factories, scientific research institutes, colleges and universities, import and export commodity inspection, textile testing in various provinces and cities.
Features
Touch screen controller: The number of frictions can be set arbitrarily.
Backup mechanical buttons for buttons in the touch screen: They can be used simultaneously, which is convenient and fast.
Pneumatic holder for specimen installation: Convenient and fast.
Equipped with a calender for adjusting the moisture content of the abrasive: The roll-off rate can be adjusted.
Complies with the standard: Appendix A of GB/T 40270 - 2021
Parameters
Stroke of the friction head: (200 ± 2) mm
Reciprocating speed: 30 times/min
Diameter of the circular friction head: (90 ± 1) mm
Outer diameter of the fixed clamp ring of the friction head: (120 ± 0.5) mm, inner diameter: (90 ± 0.5) mm
Diameter of the test washer: (113 ± 0.5) mm
Foam plastic washer: Diameter 105 mm, thickness 8 mm, unit area mass approximately 270 g/m²
Total mass of the friction load: (595 ± 7) g
Sandpaper: 600 - grit aluminum oxide water - washable sandpaper
Power supply: AC 220V, 50Hz
Отправить запрос, связаться с поставщиком
Другие товары поставщика
 |
MST clothing pressure tester-QINSUN | Product Introduction The MST Clothing Pressure Tester/Underwear Pressure tester is used in the body or in the laboratory to easily measure the pr... |
 |
Geosynthetic direct shear drawing friction tester | The friction characteristics of the interface of sand/geotextile were determined by testing the contact surface of standard sand/geotextile. This i... |
 |
Taber Abrasion Tester (Double-Head) | Standards DIN Standards: DIN 53754 (plastics), DIN 53109 (paper/board), DIN 52347 (glass/plastics) ASTM Standards: ASTM D1044 (transparent plas... |
 |
Manual Tear Strength Tester | I. Product Overview TheManual Tear Strength Testeris a precision instrument designed to measure the tear resistance of materials using standardize... |
 |
Automotive Wires Dynamic Bending Tester | Standard ISO 6722: Road vehicles – Flexible cables for wiring harnesses. SAE J1128: Low-voltage primary cable for automotive applicatio... |
Похожие товары
 |
Air Permeability Tester STD- F8 | Продавец: Standard International Group (HK) Limited | The Air Permeability Tester is designed to quickly and accurately measure the breathability and p... |
 |
Surface Performance Tester STD-FB4 - A | Продавец: Standard International Group (HK) Limited | Introduction TheSurface Tester analyzes finger movements-particularly, strokes-performed by arti... |
 |
Compression Tester STD - FB3 - A | Продавец: Standard International Group (HK) Limited | TheCompression Tester analyzes hand movements-particularly, pushing with a finger-performed by ar... |
 |
Single - Strand Bending Tester STD - FB2 - SH | Продавец: Standard International Group (HK) Limited | Standards ASTM A370. ASTM A416. ISO6934.4 The Single Fiber Bending Tester makes it possible to ... |
 |
Bending Tester STD- FB2 - S | Продавец: Standard International Group (HK) Limited | Compliance Standards ASTM D790 (Plastics Flexural Properties) ISO 178 (Flexural Strength of Rig... |
