Fabric Fiber Shedding Degree Tester (Friction)
The Fabric Fiber Shedding Degree Tester (Friction) is an instrument used to evaluate the light-blocking performance of fabrics and is widely used in the textile industry. It calculates the light-blocking rate by simulating different light intensities and measuring the illuminance value of light passing through the fabric. The tester has an accuracy of up to +5% and is suitable for various types of fabrics, including sheet textiles and coated fabrics.
Applications
The Fabric Fiber Shedding Degree Tester (Friction) is suitable for sheet textile products such as curtain materials. It is used to measure the total visible light transmittance of the fabric to evaluate its light-blocking performance.
Standards
JIS L1005-2009 ：Textiles - Determination of light transmittance of sheet textile products
Features
Touch screen controller: The number of frictions can be set arbitrarily.
Backup mechanical buttons for buttons in the touch screen: They can be used simultaneously, which is convenient and fast.
Pneumatic holder for specimen installation: Convenient and fast.
Equipped with a calender for adjusting the moisture content of the abrasive: The roll-off rate can be adjusted.
Complies with the standard: Appendix A of GB/T 40270 - 2021
Technical Parameters
| Parameter | Specification |
|---|---|
| Stroke of the friction head | (200 ± 2) mm |
| Reciprocating speed | 30 times/min |
| Diameter of the circular friction head | (90 ± 1) mm |
| Outer diameter of the fixed clamp ring of the friction head | (120 ± 0.5) mm |
| Inner diameter of the fixed clamp ring of the friction head | (90 ± 0.5) mm |
| Diameter of the test washer | (113 ± 0.5) mm |
| Foam plastic washer | Diameter 105 mm, thickness 8 mm, unit area mass approximately 270 g/m² |
| Total mass of the friction load | (595 ± 7) g |
| Sandpaper | 600 - grit aluminum oxide water - washable sandpaper |
| Power supply | AC 220V, 50Hz |
Test Procedures
1. Sample Fixation
Lay the sample to be tested flat and fix it to the sample holder of the instrument using a pneumatic clamp.
2. Abrasive Treatment
Use the calender provided with the instrument to adjust the abrasive moisture content (roller speed can be adjusted) to obtain moistened abrasive.
3. Abrasive Installation
Install the treated moistened abrasive onto the friction head.
4. Parameter Setting
Set the required load, number of friction cycles, and friction stroke via the touch screen (or spare mechanical buttons).
5. Test Start
Start the instrument and allow the friction head to perform a set number of reciprocating friction cycles on the sample surface with the abrasive.
6. Result Evaluation
After the test, compare the fibers adhering to the abrasive with the standard sample to visually evaluate the degree of fiber adhesion, thereby characterizing the fiber shedding rate of the sample.
Отправить запрос, связаться с поставщиком
Другие товары поставщика
 |
Double Plate Thermal Conductivity Apparatus | Application Building Engineering: Used to evaluate and optimize the thermal performance of building materials to improve the insulation and heat-r... |
 |
Full Vehicle Environmental Simulation Chamber | Application The Full Vehicle Environmental Performance Test Chamber is applicable across a range of vehicle performance evaluation scenarios, incl... |
 |
Konan Tester | Product Description Conforms to the UN Recommendations on the Transport of Dangerous Goods - Manual of Tests and Criteria 11.5.1 Test 1(b): Kernan... |
 |
Particle Strength Tester | Standard ASTM D4179: Standard Test Method for Single-Pellet Pressure Resistance of Catalysts and Catalyst Carriers ASTM D6175: Standard Test Me... |
 |
Melt Mass-Flow Rate Test Machine, ASTM D1238-98 | Introduction: This machine is deisgned according to ISO1133. ASTM D1238-98 ,ISO1133; Melt flow rate was measured using automatic sampling, weighin... |
Похожие товары
 |
Full-Body Garment Stress Tester,FZ/T 70015 | Продавец: Standard International Group (HK) Limited | TheFull-Body Garment Stress Testeris a precision instrument designed to quantify the pressure exe... |
 |
Industrial Dry Cleaning Machine,industrial garment steamer | Продавец: Standard International Group (HK) Limited | TheIndustrial Dry Cleaning and Energy-Saving Dryer Machinesare designed for high-performance, rel... |
 |
MST Medical Compression Stocking Tester,compression sock tester | Продавец: Standard International Group (HK) Limited | The MST Medical Compression Stocking Tester is a professional instrument designed to evaluate the... |
 |
MMT Liquid Water Separation Tester,MMT Liquid Water Analysis Tool | Продавец: Standard International Group (HK) Limited | Applications Textile Manufacturing:Testing waterproof fabrics for outdoor gear R&D:Developi... |
 |
Dental material color stability tester | Продавец: Standard International Group (HK) Limited | Application The applications of color stability testers for dental materials are mainly reflecte... |
