Smoke Density Chamber， ISO 5659，Smoke density testing equipment

Introduction

The main principle is to measure smoke density in a particular space, cable or material produced under specific conditions of combustion or radiation. The smoke will couse the beam attenuate when passes through the smoke, the light transmittance be use to calculate ratio of the optical density and smoke density.

This machineis designed according to ISO5659. IT IS with a conical radiant furnace, heat flux can be up 50 kW / m2. and laterally positioned sample, it also can test the sample mass loss rate.

Standards

• ISO 5659-1: Plastics - smoke - Part 1: Optical Density Test Principle

• ISO 5659-2: Plastics smoke generated -Part 2: single box test to obtain optical density of the material

Structure

1. The tester is consist of cabinet, sample case, the radiation cone, ignition, light and measuring devices and other relevant control device component;

2. The structural design and control design considers the ergonomics; The test box is with full door design approach; lock design for easy one-time close the door; optimize operational processes;

3. The test has fully opened door for easy loading and unloading of samples and cleaning the box;

4. The front door hinge installation with Windows and window has block the activity window opaque visor to prevent light from entering the sealed box;

5. The controller is located in the side of the box, easy to operate. When the door is closed does not affect the view controller;

6. Security flameout board, replace the simple, safer operation;

7. Which provides gas measurement port for gas toxicity test;

8. The test box for easy cleaning and coating chemical resistance;

Combustion system

1. The heating cone: Power 2600W, input temperature range of 0 ~ 1000 ºC, can be stable within ± 2 ºC within 50 minutes, providing irradiance 10KW / m²-50KW / m² of.

2. The use of mass flow controllers and differential pressure sensor can improve the accuracy of piezometers and automatic leak test

3. Ignition with automatic ignition devices; flame length 30mm ± 5mm; in accordance with standards prescribed blue flame with a yellow tip;

Smoke density measuring system

1. Smoke density and temperature are digital display, viewing more convenient, more accurate values

2. Photodetector assembly includes a photomultiplier, amplified filters, shutters, filters, neutral density filter, a lens, an optical window, and other components;

3. The light source is 6.5V incandescent light sources;

4. The installation of optical cartridge box at the top, light accepted as side-on photomultiplier, light transmission rate of 0.001% accuracy can be achieved

5. Achromatic lens

6. Japan imported Photomultiplier tubes

7. High-gain low-noise amplifier control circuit

Specification

1. Automatic completion of the test; automatic acquisition of various signals; And test report could be print from computer.

2. Brand computers,

3. The printer is optional

4. Voltage: 220V Power 4KW;

5. Customer-owned propane gas;

Qinsun Instruments Co., LTD is a professional laboratory testing instrument manufacturer in China,Have been focusing on laboratory instrument R&D more than 30 years and have rich industry experience,Based on international testing standards,We are also the instrument supplier for BV SGS laboratory,We provide one-stop solutions for lab instruments,Free Training and Turn-Key Service,Products exported all over the world,Offer 36 month warranty and are a trustworthy partner.

Другие товары поставщика

	Suture Needle Elasticity and Toughness Tester	The Elasticity and Toughness Tester for Suture Needles is a specialized device dedicated to detecting the physical properties of elasticity and tou...
	Bone Cement Four-Point Bending Fatigue Tester	Standard YY/T 1429 (China): Specifies four-point bending fatigue tests for acrylic resin bone cements under quasi-static and cyclic loading. ISO ...
	Cork Puncture and Chip Detection Instrument	The rubber stopper puncture debris detector is a device specifically used to detect the number of debris generated during the puncture process and ...
	Photovoltaic module damp heat test chamber	The Photovoltaic Module Damp Heat Test Chamber is designed to simulate long-term tropical aging conditions for photovoltaic modules and related ele...
	Flex Durability Tester	The Flex Durability Tester is suitable for testing the rub resistance of various flexible films, composite films, and coated films. It is also know...

Все товары поставщика

Похожие товары

	Test for Flammability of Materials ,AS1530.2,Fire reaction test apparatus	Продавец: Standard International Group (HK) Limited	Introduction Thistester is developed base on thestandard AS1530.2. test for flammability of mate...
	Building Material Radiant Panel Test Machine,AS/NZS 1530.3	Продавец: Standard International Group (HK) Limited	Products This machine is designed according to AS/NZS 1530.3; Thedeviceviaagasradiantplatetohea...
	Radiant Panel Flame Spread Apparatus，fire spread test machine	Продавец: Standard International Group (HK) Limited	Description ASTM E162 is one most widely used test standard to evaluate the propagation properti...
	Single-Flame Source Tester， ISO11925-2，DIN 53438; DIN4102-1	Продавец: Standard International Group (HK) Limited	Introduction This instrument is designed according to ISO11925-2. it is used to test building ma...
	Density of Smoke from the Burning or Decomposition of Plastics，ASTM D2843 Smoke Density Test	Продавец: Standard International Group (HK) Limited	Introduction In a fire, people are often smoke suffocated or unable to escape because of the inv...