Thermal cycle wet freezing testing machine

The Thermal Cycle Wet Freezing Testing Machine is designed for comprehensive environmental testing, capable of simulating extreme temperature and humidity conditions. It provides precise control and high repeatability for accelerated aging, condensation resistance, and reliability testing of batteries, photovoltaic modules, and electronic components. Its dual-chamber design ensures simultaneous wet and dry testing, enabling efficient evaluation under multi-environment conditions.

Application

(1) Environmental performance testing of lithium-ion batteries and battery modules

(2) Design qualification and type approval testing for photovoltaic (PV) modules

(3) Reliability and durability testing of electronic control units (ECUs) and PCBA

(4) Research and development for automotive and renewable energy components

Standards

(1) IEC 61215 – Terrestrial Photovoltaic (PV) Modules: Design Qualification and Type Approval

(2) UL 1073 – Safety of Enclosures for Electrical Equipment

(3) ISO 16750-4 – Road Vehicles: Environmental Conditions and Testing for Electrical and Electronic Equipment

(4) CE Certification – Conformité Européenne

(5) RoHS Compliance – Restriction of Hazardous Substances

(6) Optional: IEC 60068 series for environmental testing of electronic equipment

Features

Extreme Environmental Simulation: -40°C to +85°C operational range; 98% RH humidity control.

Ultra-Stable Performance: ±1°C temperature stability and ≤±2°C uniformity across chamber.

Rapid Transient Response: 10°C/min heating and 7°C/min cooling with auto-tuning PID.

Energy Efficiency: Advanced insulation and heat recovery for 40% lower power consumption; ECO mode for idle periods.

Safety Features: Dual overload protection, thermal cutout, current-limiting breaker, and door interlock.

User-Friendly Interface: 10” touchscreen HMI with preloaded test profiles and customizable hold times.

Remote Monitoring: Wi-Fi/Ethernet connectivity with real-time alerts via SMS or .

Glovebox Compatibility: Controlled oxygen and moisture levels for sensitive component testing.

Parameters

Parameter	Specification
Temperature Range	-40°C to +85°C (operational)
Temperature Fluctuation	≤ ±1°C
Temperature Deviation	≤ ±1°C (steady state)
Temperature Uniformity	≤ ±2°C (empty chamber)
Heating Rate	10°C/min (typical, configurable)
Cooling Rate	7°C/min (typical, configurable)
Humidity Range	30%–98% RH (non-condensing)
Humidity Deviation	±3% FS (at 85% RH ±2%, 90% RH ±2%)
Chamber Volume	500 L (standard), expandable to 1,500 L
Power Supply	380V/415V, 3-phase, 50/60Hz
Dimensions (W×D×H)	1,200 mm × 1,800 mm × 2,000 mm
Weight	800 kg (net) / 1,200 kg (gross)

Accessories

(1) Universal sample racks (4 pcs, adjustable for batteries, PV modules, or PCBAs)

(2) Humidity sensor calibration capsules (10 pcs)

(3) Software Suite: EnviroTest Pro license for Windows/Linux, including 1-year cloud test report access

(4) Calibration and Safety: NIST-traceable temperature/humidity logger, emergency portable eyewash station

(5) Maintenance Kit: Spare heating elements, refrigerant filters, chamber cleaning solution (non-corrosive)

(6) Documentation: Multilingual quick-start guide, compliance certificates for IEC/UL/ISO standards

Test Procedures

Install test samples in universal sample racks and close chamber doors securely.

Set test parameters on the touchscreen HMI or select a preloaded IEC/UL test profile.

Adjust target temperature, humidity, heating/cooling rate, and test duration as required.

Start the test sequence; system performs automated ramping and environmental cycling.

Monitor real-time conditions via touchscreen or remote connectivity.

At completion, allow chamber to return to ambient temperature before retrieving samples.

Export test reports via software interface for analysis.

Maintenance Information

Regularly inspect and clean chamber surfaces to avoid residue accumulation.

Replace HEPA filters, heating elements, and refrigerant filters as recommended by the manufacturer.

Perform NIST-traceable calibration of temperature and humidity sensors annually.

Verify door interlocks and emergency shutdown circuits before each test series.

Store the unit in a dry, ventilated environment when not in use.

Другие товары поставщика

	Liquid Sustained Combustion Tester	Product Introduction This product complies with "Recommendations on the Transport of Dangerous Goods - Manual of Tests and Criteria" 32.5.2 Test L...
	Floor Caster Durability/Wear Resistance Tester (for Floor Caster Wear Tester)	Meet the standard: GB/T 11982.2. GB/T 4085. BS/EN 425. ISO 4918-2009 ASTM D6962 BS EN 425-2002 BS EN 985-2001 ISO 10581-2011 ANSI-NALFA-LF...
	VW-1 wire and cable burning tester	Product introduction VW-1 wire and cable burning tester is suitable for measuring the resistance of wire, cable or rope to flame horizontal propa...
	Metal ring friction and wear testing machine	Evaluate the wear resistance of the material: By simulating the friction process, real-time monitoring of friction, temperature, wear and other pa...
	Scratch tester STD-KK03	Introduction With the continuous expansion of the use of plastic molding products, from the point of view of the surface appearance of molded prod...

Все товары поставщика

Похожие товары

	Falling Sand Abrasion Test machine	Продавец: Standard International Group (HK) Limited	The sand abrasion tester is a specialized testing device used to evaluate the abrasion resistance...
	Conveyor Belt Drum Friction Testing Machine	Продавец: Standard International Group (HK) Limited	Main Purposes of Conveyor Belt Drum Friction Testing Machine The conveyor belt drum friction tes...
	Dry Sand Rubber Wheel Wear Tester	Продавец: Standard International Group (HK) Limited	The dry sand rubber wheel abrasion tester is mainly used to test the abrasion resistance of mater...
	Sliding Bearing Fatigue Testing Machine	Продавец: Standard International Group (HK) Limited	The sliding bearing fatigue testing machine is an important testing device, mainly used to evalua...
	High temperature vacum friction & wear tester	Продавец: Standard International Group (HK) Limited	The working principle of a high-temperature vacuum friction and wear testing machine is to simula...