Photovoltaic module damp heat test chamber

The Photovoltaic Module Damp Heat Test Chamber is designed to simulate long-term tropical aging conditions for photovoltaic modules and related electronics. By combining high temperature and high humidity control, the system enables accelerated evaluation of module reliability, encapsulant degradation, and potential PID (Potential Induced Degradation) effects. It is suitable for R&D laboratories, quality assurance, and certification testing in compliance with international standards.

Application

Accelerated aging tests of photovoltaic modules under high temperature and humidity.

Evaluation of PID resistance and encapsulant performance.

Reliability testing of batteries, PV modules, and electronic assemblies in wet and humid conditions.

Indoor certification and R&D testing for IEC/UL compliance.

Standards

IEC 61215: Terrestrial Photovoltaic (PV) Modules – Design Qualification and Type Approval

UL 1073: Standard for Safety for Enclosures for Electrical Equipment

ISO 16750-4: Road Vehicles – Environmental Conditions and Testing for Electrical and Electronic Equipment

CE Certification (Conformité Européenne)

Features

Extreme Environmental Simulation: 85°C ±2°C / 85% RH control replicates 10+ years of tropical aging in 1,000 hours.

Ultra-Stable Performance: ±1°C temperature stability and ≤2°C uniformity for consistent long-term testing.

Energy Efficiency: Advanced insulation and heat recovery reduce power consumption by 40%; ECO mode for auto power-down during stabilization.

Safety First: Dual overload protection with thermal cutout and door interlock system.

Smart Diagnostics: AI-powered degradation prediction using IV curve shifts and EL imaging data; remote monitoring via 4G/LTE.

Flexible Operation: Dual-chamber design enables simultaneous wet/dry testing; modular expansion up to 1,500 L for full-size PV arrays.

User-Friendly Interface: 10” touchscreen HMI with preloaded IEC/UL test profiles and automated condensation drainage.

Glovebox Compatibility: Oxygen/moisture controlled operation for sensitive electronics.

Parameters

Parameter	Specification
Temperature Range	30°C to 85°C (operational)
Temperature Stability	±1°C (at 85°C setpoint)
Temperature Uniformity	≤±2°C (empty chamber)
Humidity Range	30%–95% RH (non-condensing)
Humidity Stability	±2.5% RH (at 85% RH)
Chamber Volume	500 L (standard), expandable to 1,500 L
Power Supply	380V/415V, 3-phase, 50/60Hz
Dimensions (W×D×H)	1,200 mm × 1,800 mm × 2,000 mm
Weight	800 kg (net) / 1,200 kg (gross)

Accessories

Testing Kit: 4x universal sample racks (adjustable for batteries/PV modules/PCBAs), 10x humidity sensor calibration capsules

Software Suite: License key for EnviroTest Pro (Windows/Linux), 1-year free access to cloud-based test report generator

Calibration & Safety: NIST-traceable temperature/humidity logger, emergency eyewash station (portable)

Maintenance Kit: Spare heating elements and refrigerant filters, chamber cleaning solution (non-corrosive)

Documentation: Multilingual quick-start guide (printed + digital)

Test Procedures

Install test samples securely on the sample racks.

Set desired temperature and humidity profile using the touchscreen HMI.

Initiate the test cycle and monitor chamber conditions.

Record environmental data and any module performance changes throughout the test.

Complete the test and perform post-test inspection of modules or assemblies.

Export test reports for analysis or certification documentation.

Maintenance Information

Inspect heating elements, humidity sensors, and chamber seals regularly.

Clean interior surfaces and drainage channels to prevent mold or corrosion.

Verify calibration of temperature and humidity sensors periodically with NIST-traceable standards.

Replace worn or degraded components (heating elements, filters) according to operational hours.

Ensure safety interlocks and emergency systems are functional before operation.

Другие товары поставщика

	Dry and Wet Retroreflectometer	The Dry and Wet Retroreflectometer, also known as the Dry and Wet Sand Abrasive Wear Testing Machine, is designed to evaluate the wear resistance o...
	Micro Controll High-temperature Friction Tester	Applicable Standards When conducting tests, the microcomputer - controlled high - temperature friction testing machine usually needs to comply wit...
	Alcohol burner combustion tester	This tester is developed and manufactured in accordance withAlcohol burner combustion tester; The instrument is suitable for non-metallic products ...
	Standard light source sample table	Standards ISO 3664:2009: Meets international standards for graphic arts and photography view conditions. DIN 6173-2: European norm for illuminant...
	Flip Phone Endurance Testing Equipment (for Flip Phone Durability Tester)	Product Introduction: Mobile clamshell testing machine is a special equipment for mobile clamshell fatigue test. Its structure design is reason...

Все товары поставщика

Похожие товары

	Thrust Bearing Rolling Friction and Wear Testing Machine	Продавец: Standard International Group (HK) Limited	Applicable Standards: ASTM D3702 ASTM G99 ASTM G77 ISO 18535 Product Advantages: Simulates ...
	Falling Sand Abrasion Test machine	Продавец: Standard International Group (HK) Limited	The sand abrasion tester is a specialized testing device used to evaluate the abrasion resistance...
	Conveyor Belt Drum Friction Testing Machine	Продавец: Standard International Group (HK) Limited	Main Purposes of Conveyor Belt Drum Friction Testing Machine The conveyor belt drum friction tes...
	Dry Sand Rubber Wheel Wear Tester	Продавец: Standard International Group (HK) Limited	The dry sand rubber wheel abrasion tester is mainly used to test the abrasion resistance of mater...
	Sliding Bearing Fatigue Testing Machine	Продавец: Standard International Group (HK) Limited	The sliding bearing fatigue testing machine is an important testing device, mainly used to evalua...