Falling Sand Abrasion Tester

• 

The falling sand abrasion tester is used to test the abrasion resistance of coatings under standard conditions. This method tests the abrasion resistance of a coating by dropping abrasive material through a tube from a specified height onto a coated test panel until the substrate of the panel is exposed and visible.

Application

Helmet abrasion resistance sand test machine is mainly used to test motorcycle helmets, sports helmets, electric vehicle helmets, fire helmets, rescue helmets, military and police helmets, pilot helmets and other helmets eye protection performance. Widely used in a variety of helmets related to the production of research and development, scientific research, quality supervision and testing, colleges and universities laboratories and other units.

Standards

GB811-2022:Helmets for motorcycle and electric bicycle users

GB24429:Sports helmets — Safety requirements and test methods for helmets used in bicycling, skateboarding, roller skating

GJB1564A:General specifications for flight protective helmets

GA293:Ballistic helmets and face shields for police

GA294:Police anti-riot helmets

GA295:Motorcycle helmets for police

GA296:Service helmets for police

ASTMD968:Standard Test Methods for Abrasion Resistance of Organic Coatings by Falling Abrasive

Features

1、The speed regulator can carry out the adjustment of the sample speed, and real-time display.

2、Sand fall gravity tube has three sections of PVC, acrylic or stainless steel tube.

3、Conical sand drop storage port, easy to store the sand drop.

4、The conical design structure at the bottom of the equipment and the low falling disk are convenient to collect the falling sand.

Parameters

Accessoriess

Funnel device

Sand guide tube

Sample holder

Rotating workbench, etc.

Test Procedures

Preparation of test specimens: Prepare test specimens according to standard requirements and condition them at (23±2)℃ and (50±5)% relative humidity for 24 hours.

Instrument calibration: Pour a predetermined amount of sand into the funnel, check the sand flow falling from the lower end of the guide tube, and calibrate the device using the bottom adjustment screw until the center of the sand stream is precisely centered when viewed from two positions 90 degrees apart.

Parameter setting: Set the corresponding test parameters according to the test specifications, including the sand falling speed, time, and the type and particle size of the abrasive sand.

Testing process: Install the sample in the test position of the instrument, start the equipment, and allow the abrasive sand to fall onto the sample surface and cause friction and abrasion.

Data recording: After the test, remove the sample, carefully clean it, and record the change in sample mass to calculate the wear amount.

Results analysis: Analyze the test results, evaluate the wear resistance of the material, and compare it with relevant standards or requirements to generate the final test report.

Другие товары поставщика

	Fabric thickness tester	Fabric thickness tester mainly used to measure the thickness of the fabric, suitable for leather, rubber and textiles and other materials, the thic...
	Light Fastness Test Instrument丨Light Fastness Tester	Features and Benefits 1.The lightfastness test instrumentusexenon arc lamp as a radiation source, the visible light range emitted is 380nm-750nm...
	Air Permeability Tester STD- F8	The Air Permeability Tester is designed to quickly and accurately measure the breathability and permeability of a wide range of samples, from those...
	STD Battery short-circuit tester丨STD Battery short-circuit chamber	Product Introduction Battery Short Circuit Tester is a device that can be applied to the external short circuit test process of lithium ion batter...
	Falling Sand Wear Tester	Applicable Standard JG/T 133-2000 ASTM D968-83 ASTMD333 ASTMD1395 ASTMD2205 Main Purposes It is mainly used to test the abrasion - resistanc...

Похожие товары

	Falling Sand Abrasion Test machine	Продавец: Standard International Group (HK) Limited	The sand abrasion tester is a specialized testing device used to evaluate the abrasion resistance...
	Conveyor Belt Drum Friction Testing Machine	Продавец: Standard International Group (HK) Limited	Main Purposes of Conveyor Belt Drum Friction Testing Machine The conveyor belt drum friction tes...
	Dry Sand Rubber Wheel Wear Tester	Продавец: Standard International Group (HK) Limited	The dry sand rubber wheel abrasion tester is mainly used to test the abrasion resistance of mater...
	Sliding Bearing Fatigue Testing Machine	Продавец: Standard International Group (HK) Limited	The sliding bearing fatigue testing machine is an important testing device, mainly used to evalua...
	High temperature vacum friction & wear tester	Продавец: Standard International Group (HK) Limited	The working principle of a high-temperature vacuum friction and wear testing machine is to simula...