Single chip liquid crystal touch impact testing machine

• 

Product Introduction:

Liquid crystal touch impact testing machine is mainly used for hard plastics (including sheet, pipe, plastic profile)， reinforced nylon, glass fiber reinforced plastic, ceramic, cast stone, electrical insulation materials and other non-metallic materials impact toughness measurement, widely used in the chemical industry, scientific research units, universities and other quality testing departments.

Standards:

GB/T 18910.101-2021

IEC 60068-2-75:2014

Main features:

Not poor quality: the use of high hardness and high-precision bearings, and the use of shaftless photoelectric sensors, fundamentally eliminate the loss caused by friction, to ensure that the friction energy loss is far less than the standard requirements.

Intelligent prompt: According to the impact of the situation, intelligent prompt working status, always interact with the experimenter, to ensure the success rate of the test.

Friendly interface: there are parameter setting interface - result query interface - measurement interface - system setting interface, each operation has a clear user prompt, you can record 10 test records, you can choose domestic and international standards, you can choose Chinese and English.

Accurate measurement: In full accordance with the provisions of the new standard, after 10 swing cycles for a calculation of energy loss, each measurement to go through 3 times to average, to ensure the accuracy of energy loss.

Performance parameters:

1. Simple beam impact testing machine

- Impact speed: 2.9m/s

- Impact energy: 1/2/4/5J

- Maximum friction loss energy: <0.5%

- Pendulum prelift Angle: 150±1°

- Strike center distance: 230mm

- Power supply: 220VAC-15% —— 220VAC+10%, 50Hz(single-phase three-wire system)

2. Cantilever beam impact testing machine

- Impact speed: 3.5m/s

- Impact energy: 1J; 2.75 J; 5.5 J; 11J; 22J(3 hammers, customer's choice)

- Maximum friction loss energy: <0.5%

- Pendulum prelift Angle: 150±1°

- Strike center distance: 335mm

- Power supply: 220VAC-15% —— 220VAC+10%, 50Hz(single-phase three-wire system)

Другие товары поставщика

	Car seat center of gravity measuring tester	Getaquote:Whats/App: +86 181 0160 0864 The Car Seat Center of Gravity Measuring Tester is a precision testing instrument used to determine the cen...
	Perforated Leather Abrasion Tester	Get a quote： Whats/App: +86 181 0160 0864 The Perforated Leather Abrasion Tester is designed to evaluate the abrasion resistance and surface dura...
	Bag Plastic Buckle Durability Tester	Get a quote： Whats/App: +86 181 0160 0864 Web: gellowen.co.uk It is mainly used to test the service life of plastic plug-ins in luggage accessor...
	Water Leak Detector	Get a quote： Whats/App: +86 181 0160 0864 Web: gellowen.co.uk The Water Leak Detector primarily measures the volume and rate of gas released whe...
	Safety shoe impact testing machine / Safety shoes testing machine	According to the criteria Bs-953.1870 EN-344. ANSI-Z41 CSA-Z195 ISO K88782 EN ISO 20344. ANSI-Z41 BS EN-344 CSA-ZI95 LD50-1994 Product F...

Похожие товары

	Bottle Wall and Bottom Thickness Tester	Продавец: Standard Group (Hong Kong) Limited	The wall and bottom thickness tester for bottles is a measuring instrument widely used in the pha...
	Pinhole Tester / Pinhole Testing Equipment	Продавец: Standard Group (Hong Kong) Limited	The pinhole tester for aluminum foil is a device specifically used to detect micro - pinholes in ...
	Cork Puncture and Chip Detection Instrument	Продавец: Standard Group (Hong Kong) Limited	The rubber stopper puncture debris detector is a device specifically used to detect the number of...
	Aluminum Ointment Tube Toughness Tester	Продавец: Standard Group (Hong Kong) Limited	The ductility tester for aluminum tubes is a device specifically used to detect the ductility ind...
	Vacuum leak tester / Vacuum leak instrument	Продавец: Standard Group (Hong Kong) Limited	Vacuum Decay Leak Tester specializes in the detection of leaks in ampoules, vials, injection bott...