Abrasion testing machine / Abrasion Testers
Product Introduction
Wear testing machine is used with the balance, specially testing the wear resistance of rubber products such as soles, tires, car tracks, etc. The counters are electronic automatic, which can set the wear revolution, and automatically stop when the set revolution is reached.
Standard
GB/T 1689 standard, ISO:4661-1:1993. ISO 2481:1988. ISO 471:1983. ISO 1826:1981
Test size
Outer diameter 2 ", inner diameter 1/2 ", thickness 1/2 ", circumference 220mm, hardness 60——70
Machine operation method
1. Prepare the core of the specimen according to the conditions of obtaining the specimen. And record its exact weight.
2. Fix the specimen core on the core shaft seat, and then adjust the Angle of the specimen. (Usually set to 15∘)
3. Different test methods are divided into high standards and low standards according to material requirements.
3.1 High standard requirements:
a. Angle (the Angle between the test piece and the grinding wheel)15∘
b. Load :6 pounds
c. Pre-grinding revolutions :300 revolutions
d. Remove the specimen core, brush with a clean brush to remove the powder, then weigh the exact weight with a precision balance, and record the weight of the sample before the test
e. Install the specimen core and set the wheel rotation times :3000 revolutions
f. After the wear is completed, remove the specimen, brush with a clean brush to remove the powder, and then weigh the accurate weight with a precision balance, which is the weight of the sample after the test
g. Substitute the formula to calculate the grinding amount
3.2 Low standard requirements:
a. Angle (the Angle between the test piece and the grinding wheel)15∘
b. Load :2 pounds
c. Pre-grinding revolutions :200 revolutions
d. Remove the specimen core, brush with a clean brush to remove the powder, then weigh the exact weight with a precision balance, and record the weight of the sample before the test
e. Load back the specimen core and set the wheel rotation times :2000 revolutions
f. After wearing, remove the specimen, brush with a clean brush to remove the powder, and then weigh the exact weight with a precision balance
This is the test weight after the test
g. Substitute the formula to calculate the grinding amount
4. After all specimens have been tested, remove the weight and store it, and remove the debris on the machine.
Wear value calculation method:
Wear (volume m1)== Weight before test - weight after test
Specific gravity algorithm:
a. If the test material is heavier than water
Specific gravity = Weight in air ÷(weight in air - weight of sample in water)
b. If the test material is lighter than water
Specific gravity = weight in air ÷ volume
Technical parameters
Grinding wheel diameter Φ150mm, 40mm(w)， particle size 36#
Grinding wheel speed 34±1r/min
The incline range of the test material is adjustable from 0 to 35°
Test shaft speed (GB)76±2r/min
Load 26.7N±0.2
Counter LED, 0——99.999.999
Volume (W×D×H) 60 × 50 × 45cm
Weight (approx) 60 kg
Power 1 #,AC220V, 50Hz (depending on country or designation)
Отправить запрос, связаться с поставщиком
Другие товары поставщика
 |
Fabric Drying Tester | Product Introduction: This device is developed for the automatic test of "dryness" method A and method B specified in JIS L 1096 (Fabric test meth... |
 |
Stainless Steel Envirotronics Chamber | Useful and durability | Environmental Test Chamber is designed for laboratory experiments, product reliability testing, and programmable controls, providing a wide range o... |
 |
Electric Rubbing Colour Fastness Tester-QINSUN G238CC | Introduction G238CC Electronic rubbing colour fastness tester is used for testing the color fastness of fabric and leather by dry/wet rubbing. The... |
 |
Schopper Folding Endurance Tester ISO 5626 | Use and Scope of application: 1. the instrument is suitable for tensile strength greater than 1.33kn/m, thickness less than 0.25mm paper folding d... |
 |
ISO 12103-2 M2 Test Dust | Product Introduction: Particle Technology Fuel Contamination Test Dust offers a full range of fuel contamination test materials used to test the r... |
Похожие товары
 |
Bottle Wall and Bottom Thickness Tester | Продавец: Standard Group (Hong Kong) Limited | The wall and bottom thickness tester for bottles is a measuring instrument widely used in the pha... |
 |
Pinhole Tester / Pinhole Testing Equipment | Продавец: Standard Group (Hong Kong) Limited | The pinhole tester for aluminum foil is a device specifically used to detect micro - pinholes in ... |
 |
Cork Puncture and Chip Detection Instrument | Продавец: Standard Group (Hong Kong) Limited | The rubber stopper puncture debris detector is a device specifically used to detect the number of... |
 |
Aluminum Ointment Tube Toughness Tester | Продавец: Standard Group (Hong Kong) Limited | The ductility tester for aluminum tubes is a device specifically used to detect the ductility ind... |
 |
Vacuum leak tester / Vacuum leak instrument | Продавец: Standard Group (Hong Kong) Limited | Vacuum Decay Leak Tester specializes in the detection of leaks in ampoules, vials, injection bott... |
