Falling Sand Wear Tester

• 

Applicable Standard

JG/T 133-2000

ASTM D968-83

ASTMD333

ASTMD1395

ASTMD2205

Main Purposes

It is mainly used to test the abrasion - resistance of the lenses of helmet goggles and evaluate their ability to resist particle - induced damage.

Instructions For Use

1. according to the standard requirements for the preparation of test plates and placed in (23 +-2) degrees Celsius, relative humidity (50 +-5) degrees Celsius conditions for 24 hours.

2. Calibrate the apparatus:

Pour a certain amount of sand into the funnel, check the sand stream falling from the lower end of the conduit, and calibrate the device with the bottom adjusting screw until the inner part of the sand beam falls exactly on the center of the sand stream when viewed from two positions of 90 degrees Celsius each other. Use the high and low adjusting nut to adjust the distance from the tube tube to the painted surface according to the ASTM standard, when measured in the vertical direction, the near point of 1 inch (25mm), the user needs to be adjusted according to the thickness of their own samples, factory machine pre-adjustment of 25mm. to the pouring of a certain volume amount of sand (to 2000 +-10ml is appropriate), and measure the outflow time, the outflow rate should be 21S- 23.5S within 2L. This speed comes from the ASTM standard, and with the international standard sand for the test, we measured the speed of 1 minute 7L or more.

3. do the test should pay attention to, after the end of the sand fall, the machine should be slightly tilted to make the lower funnel in the small square of excess sand poured out, in the re-insertion of the sand fall switch in order to avoid the sand fall switch can not be put in.

Main Technical Parameters

Overall Dimension: 230mm×200mm×1500mm (L×W×H)

Catheter Length: 36 inches (914mm)

Catheter I.D.: 0.75 inches (19mm)

Hopper Volume: 3L

Machine Weight: 25KG

Другие товары поставщика

	Transmission belt flammability and flame diffusion characteristics tester，Accurate Flame Diffusion Measurement for Belts	Product Introduction: The conveyor belt flammability and flame diffusion tester is suitable for testing the flammability and flame propagation cha...
	Syringe slide performance tester	Application This tester is suitable for evaluating the sliding performance of various medical devices, including: (1) Disposable sterile syringes &...
	Suture Needle Elasticity and Toughness Tester	The Elasticity and Toughness Tester for Suture Needles is a specialized device dedicated to detecting the physical properties of elasticity and tou...
	Scratch tester STD-KK02	Product introduction: With the continuous expansion of the use of plastic molding products, from the point of view of the surface appearance of mo...
	Luer conical joint multi-function tester	The Luer Conical Joint Multi-Function Tester is a precision instrument designed to evaluate multiple performance characteristics of Luer-type conne...

Похожие товары

	Plastic Smoke Density Tester F313	Продавец: Standard International Group (HK) Limited	The F313 Plastic Smoke Density Tester is a precision instrument designed to measure the specific ...
	Xenon Test Chamber	Продавец: Standard International Group (HK) Limited	Features and Benefits 1.The use of xenon arc lamp as a light source, can simulate the full sunli...
	Single Cable Vertical Flame Tester	Продавец: Qinsun Instruments Co., LTD	Introduction Single Cable Vertical Flame Tester is used for the vertical flame propagation of a ...
	Safety Helmet Flammability Tester	Продавец: Qinsun Instruments Co., LTD	Product Introduction: Safety hat flame retardant performance tester for safety hat flame retarda...
	Furniture flammability tester	Продавец: Qinsun Instruments Co., LTD	Product details Furniture flammability tester is mainly used to test the combustion performance ...