.

Filter Media Tester TVE 3000

TVE 3000 for vacuum cleaner tests with dust in accordance with the standard EN 60312
With the aid of the TVE 3000, vacuum cleaner tests can be carried out more cost-effectively than in accordance with the standard EN 60312. In addition, it is possible to distinguish the separation behavior of vacuum cleaners with bags and vacuum cleaners with bags and HEPA end filters reliably with with dust or as an option with salts – e.g. NaCl or KCl within the salt generator AGK 2000. The dust disperser RBG 1000 that is used operates much more uniformly than is required in the standard and therefore delivers an optimized dust application, which is a prerequisite for exact measurements of separation efficiency with a particle measurement device.
With the particle measurement system Promo®2000 with the aid of the welas®2300 aerosol sensor in the clean gas, the emissions of a vacuum cleaner can be measured in accordance with the standard. As a result, not only is it possible to accurately compare vacuum cleaners, but the individual filter stages can also be reliably assessed.
With the particle measurement system Promo®3000, users have access to a high-resolution aerosol spectrometer for virtually simultaneous determination of the particle size distribution and the particle concentration in the raw gas and in the clean gas.
The welas®2070 aerosol sensor accurately determines the measurement in the raw gas, while the welas®aerosol sensor 2300 performs the measurement in the clean gas, allowing the fraction separation efficiency of vacuum cleaner bags and HEPA end filters to be performed. Function Dust is introduced into the system using the dust disperser RBG 1000. The reproducibility of the dust concentration is < 10% in terms of quantity.
The welas®2070 aerosol sensor measures the particle size distribution and the particle concentration in the raw gas (upstream of the vacuum cleaner). The dust is sucked in by the vacuum cleaner and separated out in the vacuum cleaner bag and in the HEPA end filter. The emissions from the vacuum cleaner are then measured with the welas®2300 aerosol sensor on the clean gas side (downstream of the vacuum cleaner). From the measurements of the raw gas and clean gas, the fraction separation efficiency of the vacuum cleaner is determined.
The FTControl software allows many fraction separation efficiency measurements for different vacuum cleaners to be displayed at the same time on screen.
Both the dust disperser and the clean gas sensor can be positioned in different locations so that the influence of the flow channel on particle sedimentation can be investigated.

Descriptions
Position of the clean gas sensor:The aerosol sensor for the clean gas measurement can be positioned in two different locations.
Position 1 is the clean gas measurement point in accordance with the standard EN 60312.
The clean gas sensor can be operated either in position 1 or position 2, e.g. in order to investigate sedimentation and other transport losses in the suction channel. Position 1 complies with the standard.
Position of the dust disperser RBG 1000:
The RBG 1000 is attached as shown in Fig. 1 in accordance with standard EN 60312 or frontally positioned at the entrance of the flow channel, which ensures that no deposits can build up in the aerosol intake elbow.
Measurement of the fraction separation efficiency
From the measurements of the raw gas and clean gas, the fraction separation efficiency of the vacuum cleaner or the vacuum cleaner filter stages is determined.



Отправить запрос, связаться с поставщиком

Кому: Тысяча сплошная точный электромеханический прибор контрольно-измерительной ЛТД
Ваш E-mail:
Текст письма:


Send to other suppliers

Другие товары поставщика

Hexapod Tumbler Carpet Tester
Hexapod Tumbler Carpet Tester IntroductionThe steel ball or the hexagonal feet randomly roll in the rotating drum, which is covered with carpet textile samples. Observe the appe...
iec60529 glow wire equipment
iec60529 glow wire equipment Brief IntroductionThe glow wire tester operation instructions according to the GB5169 and GB4706the design and manufacturing requirements with the ...
Full Face Masks Flame Resistance Tester
Full Face Masks Flame Resistance Tester Full Face Helmet Flame Resistance TesterMedical mask fire test machine is to determine the fire resistance performance of medical face masks and fu...
Pneumatic bursting strength tester
Pneumatic bursting strength tester Pneumatic bursting strength tester is widely used in textile , leather , paper and other fields. The bursting strength and height of woven, knit...
Multi Finger Scratch/Mar Tester
Multi Finger Scratch/Mar Tester Introduction: Multi Finger Scratch/Mar Tester uses tungsten carbide as a scratch to accurately detect surface damage caused by unconventional ph...
Все товары поставщика

Похожие товары

Adjustable Plastic Bar Chair with Slip-Ons DB-P11S
Adjustable Plastic Bar Chair with Slip-Ons DB-P11S Продавец: 826214
Plastic Bar Chair with Adjustable Disc Base DB-P10S
Plastic Bar Chair with Adjustable Disc Base DB-P10S Продавец: 826214
Plastic Seat Can Be Raised and Lowered Bar Chair DB-P09S
Plastic Seat Can Be Raised and Lowered Bar Chair DB-P09S Продавец: 826214
High Wooden Leg Bar Chair Without Backrest DB-P08
High Wooden Leg Bar Chair Without Backrest DB-P08 Продавец: 826214
Custom Coffee Table Bulk Wholesale From China
Custom Coffee Table Bulk Wholesale From China Продавец: Zhejiang Anji Hengchang Chair Industry Co., Ltd Features of the coffee table china: 1. solid surface material, no attributes, no penetration; Abs...