.

27dBm 1800 2100 Dual Band 3G 4G Signal Booster MGC AGC ALC

HPC-DW-27 DCS1800 and 3G 2100mhz Dual band signal repeaters A cell signal booster (also known as cellular repeater or amplifier) is a device that boosts cell signals to and from your mobile whether at home or office or in any vehicle.  It does this by taking the existing cellular signal,Website:, amplifying it, and then broadcasting to an area in need of better reception. If you're experiencing dropped calls, slow or lost internet connection, stuck text messages, poor voice quality, weak coverage, low bars, and other cell reception problems, a cell signal booster is the best solution that produces definite results. We provides signal boosters kits for any Homes, Offices, Cars, RV's, Boats and more. All amplifier kits come with Indoor and Outdoor Antennas, Cables, Power adapters and more. HPC-DW-27 Dual band repeater Features: 1.With unique appearance design, have good cooling function 2.With MGC function,(Manual Gain Control), Customer can adjust the Gain as needed ; 3.With DL signal LED display, help to install the outdoor antenna at the best state; 4.With AGC and ALC, make repeater work stable .  5.PCB with isolation function ,make UL and DL signal not influence each other, 6.Low intermodulation, high Gain ,stable Output power  HPC-DW-27 Dual band repeater Inside and Outside Design HPC-GW-27  Dual band repeater is to support any two mobile band existing in the world to help end users to improve mobile signals for much better call quality and smoother data transmission. It is designed to support coverage area max can up to 2000 square meters with proper engineering. Below are the main features. 1.The consumer repeater is an ideal solution for providing a cost effective improvement in cellular in-building coverage of a home, office, restaurant or building, in the quickest time possible. 2.Manual gain control (MGC) available for both uplink and downlink to adjust the gain value for proper coverage during installation or maintenance. 3.To maintain safe and specific output signal levels and give alarms on self-oscillation, the repeater has built-in AGC and ALC circuits, which can automatically control the gain of the repeater depending upon the strength of input signals. 4.Auto shut off function available for both uplink and downlink to avoid deep self-oscilation from jamming the towers, saving your trouble from operators.  5.Wide band feature enables all devices operating within the wide frequency range of the repeater to see an improvement in performance. 6.Multiple s and other handheld devices throughout a building can benefit from a wireless repeater. 7.Supports up to (500) users / calls simultaneously. 8.Extended battery life. (Your does not need to put out as much power due to improved reception.) Specification of HPC-GW-27 Dual band repeater: Electrical specification Uplink Downlink Frequency Range GSM900 & EGSM 880 ~ 915 MHz 925 ~ 960 MHz DCS 1920 ~ 1980 MHz 2110 ~ 2170 MHz Max .Gain ≥ 70dB ≥ 75dB Max .Output Power ≥ 24dBm ≥ 27dBm MGC ( Step Attenuation ) ≥ 31dB / 1dB step Automatic Level Control ≥ 20dB Gain Flatness GSM & CDMA Tpy≤ 6dB(P-P); DCS,PCS ≤ 8dB(P-P) WCDMA ≤ 2dB/ 3.84MHz,Full Band ≤ 5dB(P-P) Noise Figure ≤ 5dB VSWR ≤ 2.0 Group Delay ≤ 1.5μs Frequency stability ≤ 0.01ppm Spurious Emission & Output inter-modulation GSM Meet  ETSI TS 151 026 V 6.1.0 WCDMA Meet 3GPP TS 25.143 ( V 6.2.0 ) CDMA Meet  IS95 & CDMA2000 WCDMA System Spurious Emission Mask Meet 3GPP TS 25.143 ( V 6.2.0 ) Modulation Accuracy ≤ 12.5% Peak Code Domain Error ≤ -35dB@Spreading Factor 256 CDMA System Rho ρ > 0.980 ACPR Meet IS95 & CDMA2000 Mechanical  Specifications Standard I /O Port N-Female Impedance 50 ohm Operating Temperature -25ºC~+55ºC Environment Conditions IP40 Dimensions 220x320x40mm Weight ≤ 3.00Kg Power Supply Input AC90-264V,output DC 5V / 6A LED  Alarm Standard Power LED Power Indicator UL LED Be lighted when there is calling DL 1 Be lighted when Outdoor signal is -65dB DL 2 Be lighted when Outdoor signal only -55dB DL 3 Be lighted when Outdoor signal only -50dB The installtion of the Repeater Outdoor antenna ( for receiving the signal from the BTS ) + Cable ( transfering the received signal) + Repeater ( for amplifying the received signal) + cable( for transfering the amplified signal) + indoor antenna( for shooting the amplified signal),  (Note : Omni indoor antenna is 3dBi,it can work with about 200m2 . If need repeater coverage larger area , need add more antenna,the HPC-GW-27 Max can work with 10pcs indoor antenna.  ( when add antenna ,please remember to take splitters ) Installation steps  Step 1 Start by taking your up to the roof or other location outside to find where the signal is strongest. Step 2 Temporarily mount the Outdoor (outside) antenna in that location. You may need to adjust and move the antenna later. Step 3 Run coaxial cable into the building to a convenient loaction (attic, etc.) where you can also get standard power for the Signal Repeater. Step 4 Place the Signal Repeater in that location and connect the coaxial cable to the Outdoor Side of the Signal Repeater and the Outdoor antenna. Step 5 Mount your Indoor (inside) antenna in a productive location. You may need to adjust or move the antenna later. More notes on Indoor antennas and patterns here. Step 6 Connect coaxial cable between the Indoor antenna and the Signal Repeater output port. Step 7 Power up the system and check for signal inside the building. If needed, tune system by moving and or pointing the Outdoor and Indoor antennas until they get the most signal possible. Step 8 Secure all antennas and cables, securely mount the Signal repeater and clean up the installation. Of course there are still a few more things to consider but in general, this is the basic procedure. For more information, please contact us. Terms and Conditions Certificate CE/RoHs Country of Origin China Port of Dispatch Shenzhen Production Capacity 1000pcs/month Date of Delivery Within 3 days after received payment inform MOQ 10pcs Warranty 2years Pacakge 1pcs/box; 5pcs/carton Country of Origin China


Отправить запрос, связаться с поставщиком

Кому: Shenzhen Sai Tong Tian Electronic Technology Co.,LTD
Ваш E-mail:
Текст письма:


Send to other suppliers

Другие товары поставщика

Smart mobile signal booster are main used to improve the sginal in the weaker signal situtation, meanwhile, it can also up speed the networks of 2G...
4G LTE Mobile Signal Repeater ST-4G Max coverage 1000sqm LTE 4G Signal Booster Repeater Amplifier IndoorIf you’re suffering from bad cell receptio...
2watts GSM900mhz signal booster ST-900&2W Max coverage 3000sqm What is the booster?Cell signal booster (also named repeater,Website:, amplifier) i...
Original Xiaomi Wifi Amplifier Mi Router Wireless Wi-Fi Repeater Network Router Extender Signal Amplifie Antenna Wifi Repeater   Main Features:-Lig...
HPC-GDW-27 GSM900 DCS1800 3G 2100 Tri band signal repeatersA cell signal booster (also known as cellular repeater or amplifier) is a device that b...
Все товары поставщика

Похожие товары

Optical Fiber Head
Optical Fiber Head Продавец: KUNSHAN JINLONGYUAN NEW MATERIAL TECHNOLOGY CO.LTD Optical fiber interface is a physical interface used to connect optical fiber cables. FC is the a...
Mobile Phone Clip
Mobile Phone Clip Продавец: KUNSHAN JINLONGYUAN NEW MATERIAL TECHNOLOGY CO.LTD MIM stand for Metal Injection Molding, it's a forming method of a metal parts and can provide a n...
Mobile Phone Camera
Mobile Phone Camera Продавец: KUNSHAN JINLONGYUAN NEW MATERIAL TECHNOLOGY CO.LTD This is generally called the mobile camera module, or directly called the camera. This kind of ca...
Medical Treatment
Medical Treatment Продавец: KUNSHAN JINLONGYUAN NEW MATERIAL TECHNOLOGY CO.LTD Jlymim provides basic surgical instruments, biopsy forceps, high frequency electric knife nickel ...
Medical Cosmetic Protractor
Medical Cosmetic Protractor Продавец: KUNSHAN JINLONGYUAN NEW MATERIAL TECHNOLOGY CO.LTD MIM stand for Metal Injection Molding, it's a forming method of a metal parts and can provide a n...