Hydraulic Liner Hanger Tie-Back Assembly

The tie-back assembly is a special cementing tool for tieback operation.

Tieback equipment allows existing liners with a receptacle to be extended to the surface or farther up hole, and provides a high-pressure seal at the top of a cemented or uncemented liner. TIW offers variety of tieback seal nipples and tieback packers to accommodate liner top extension and remedial operations. Today, some new types of drilling liner tieback equipment are developed due to the annular gas channeling in high-pressure oil-gas well even after tie back cementing.

Tie back liner procedureof Hydraulic Liner Hanger Tie-Back Assembly

Measure and drift the casings carefully and clean all the threads.

Calculate the kelly-up of the casing (the particular part of the last casing which is above the rotary table) and arrange the casing string.

Prepare several casings, which are approximately 0.5m shorter than the others and convenient for kelly-up calibration. (The actual kelly-up is not equal to the calculated value due to measurement error and the remaining threads of the casings.)

Connect the milling shoe and trip in. Polish the inner surface of the polished bore receptacle, make sure there is no debris.

Note the depth of the milling shoe when it reaches the top of the seal assembly (judge from the changes on pressure and WOB). Then lift the drill string for 1m.

Use a drilling rate of 40～50rpm and a normal flow rate. Slowly lower the drill string. Polish the inner surface of the polished bore receptacle twice or three times. Each time polish 3～4min. During the last polishing, apply an additional load of 2～3t when the torque suddenly increases (the milling shoe reaches the top of the seal assembly) during the last polishing. Polish for another 2~3min and note the depth of the milling shoe, which is an important clue for the casing setting depth.

Circulate with high flow rate for 5min.

Trip out and check the milling shoe. If there is a circle of polished trace and the diameter is equal to the I.D. of the left thread on the seal assembly, then the milling shoe have reached the bottom of the polished bore receptacle.

Features of Hydraulic Liner Hanger Tie-Back Assembly

With the guide shoe and circulate bore, it can stab into polished bore receptacle before cementing, more convenient than conventional cementing which pumps down cement before stabbing.

With its streamline shape, the guide shoe can stab into polished bore receptacle easily.

The Tieback Seal Assembly with three stacks of molyglass seal is designed for high-pressure and high-temperature liner tieback completions. Available in seal length is 1.2m.

As one of the top reliable liner hanger companies in China, Saigao has been devoted in the production of hydraulic liner hanger products. Drop us messages for any query to know more about Saigao and Saigao products.

Technical Parameters ofHydraulic Liner Hanger Tie-Back Assembly

Specifications, mm	Φ177.8	Φ127.0
Sealing capacity, MPa	25	25
Heat-proof Rating, ℃	120	120
Available Sealing Length, mm	1200	1200
	Φ155	Φ108

,

As one of the most professional oil well equipment manufacturers, Saigao Groupprovides oilfield cementing tools, tie back receptacle, tie back casing, liner hanger assembly, hydraulic hangercasing tie back, tie back liner and etc. Saigao products are not only popular in China, but also exported to Russia, Brazil, Australia, South Africa and other countries and regions.

Other supplier products

	BW1200 / 7 Horizontal Double Cylinder Reciprocating Double Acting Piston Pump	BW1200/ 7 slurry pump is a horizontal double cylinder reciprocating double-action piston pump. The power has electric driving and diesel driving. ...
	Wire Wrapped Screen Pipe	The continuous-slot well screen is widely used throughout the world for water, oil, and gas wells, and is the dominant screen type used in the wate...
	Non-rotating Stabilizer	Non-rotating stabilizer(rubber sleeve stabilizer) is able to avoid blade wear and wall damage during. The non-rotating stabilizer consists of mandr...
	Perforated Pipe	In the drilling process, in order to prevent the collapse of the hole wall, sand (water), water leakage, or to separate the water layer, the metal ...
	Orientation Sub	Orientation subis a major power deflection tool having a fixed angle deviated from low end thread of the bent sub to axial line of drill stem, the ...

All supplier products

Same products

	YC160W Wheel excavator YC160W	Seller: Guangxi Yuchai Equipment Technology Co., Ltd	YC160W Wheel excavator YC160W wheel excavator is a new generation of full hydraulic wheel excavat...
	Yuchai U20 mini excavator	Seller: Guangxi Yuchai Equipment Technology Co., Ltd	Yuchai U20 mini excavator Improvements in Over 80 Details: Tailless Excavator U20 is a Yuchai ...
	Yuchai YC80 small excavator	Seller: Guangxi Yuchai Equipment Technology Co., Ltd	Yuchai YC80 small excavator International brand engine It is equipped with Yanmar 4TNV98C natur...
	Top Type Hydraulic Breaker	Seller: Guangxi Yuchai Equipment Technology Co., Ltd	Top Type Hydraulic Breaker With the higher restriction of blasting control,hydraulic breakeris w...
	Manual Cartoon Hospital Pediatric Bed	Seller: Hengshui Defeng Medical Equipment Co.,Ltd	Manual Cartoon Hospital Pediatric Bed This Manual Hospital Pediatric Bed has all the necessary ...