ADSS Fiber Optic Cable
Fiber Optic ADSS Cable is known as an all-dielectric self-supporting optical cable. Self-supporting ensures that the ADSS outdoor fiber cablehas sufficient mechanical strength. The ADSS fiber cable applies all-dielectric material to withstand the impact of strong electricity in a high voltage and strong current environment. As one of the most professional ADSS cable suppliers and manufacturers, TUOLIMA can customize the self-supporting fiber optic cable ADSS according to your requirements. If you need any technical support, we will also recommend the most suitable and cost-effective customized ADSS OFC cable for you according to the different application environments, laying methods, and customer requirements. Our all-dielectric self-supporting cables can be applied in many areas, for example, the aerial industry. You can check ADSS fiber specsbelow. If you have any questions, please feel free to contact us.
Specification of ADSS Fiber Optic Cable
|
Mechanical characteristic and test method |
||
|
Tensile strength |
conform to IEEEC standard P |
|
|
Crush |
conform to IEC 794-1-E3 |
|
|
Impact |
conform to IEC 794-1-E4 |
|
|
Repeated bending |
conform to IEC 794-1-E6 |
|
|
Torsion |
conform to IEC 794-1-E7 |
|
|
Flexing |
conform to IEC 794-1-E8 |
|
|
Cable bend |
conform to IEC 794-1-E11 |
|
|
Water penetration |
conform to IEC 794-1-F5B |
|
|
Color coding |
conform to EIA/TIA 598 |
|
|
Temperature requirement |
operation: Installation |
- 40 C~ +60 C - 10 C ~ +60 C |
|
storage/transportation |
- 40 C ~ +60 C |
|
|
Temperature cycling test |
conform to IEC 794-1-F1 |
|
|
Bending Radius |
unloaded |
15 times of outer diameter |
|
loaded |
25 times of outer diameter |
|
Characteristics of ADSS Fiber Optic Cable
|
Fiber Material |
G652D |
|
Mode field diameter (1310nm): |
|
|
Mode field diameter (1550nm): |
|
|
Cladding diameter: |
125um±1.0um |
|
Cut off wavelength of cabled fiber (ℷcc): |
≤1260nm |
|
Attenuation at 1310nm: |
≤0.36dB/km |
|
Attenuation at 1550nm: |
≤0.22dB/km |
|
Bending loss at 1550nm (100 turns, 30mm radius): |
≤0.05dB |
|
Dispersion in the range 1288 to 1339nm: |
≤3.5ps/(nm•km) |
|
Dispersion at 1550nm: |
≤18ps/(nm•km) |
|
Dispersion slope at zero dispersion wavelength: |
≤0.092ps/(nm2•km) |
Details of ADSS Fiber Optic Cable
|
SN |
Item |
Unit |
Value |
|
1 |
count |
12~288 |
|
|
2 |
Number of fibers per tube(max) |
count |
4 |
|
3 |
Number of elements |
count |
6 |
|
4 |
Cable diameter |
mm |
|
|
5 |
Cable weight |
kg/km |
121 |
|
6 |
Max allowed operating tension |
N |
5000 |
|
7 |
Short term crush |
N/100mm |
2200 |
|
8 |
Max span with 1.0% installation sag |
m |
100 |
Drawing of ADSS Fiber Optic Cable
Advantages of ADSS Fiber Optic Cable
Uninterruptible power supply erection
Adopt PE/AT sheath, excellent resistance to erosion
Small cable diameter and lightweight help reduce the impact of ice, wind, and load on towers
Large span, maximum span ≥ 1000 meters
Great tensile strength and high/low temperature resistance
Service life is expected over 30 years
Packing and Comments of ADSS Fiber Optic Cable
Packing material: Non-returnable wooden drum.
Both ends of the outdoor optical cable are securely fastened to the drum and sealed with a shrinkable cap to prevent ingress of moisture.
Cable printing: The sequential number of the cable length shall be marked on the outer sheath of the cable at an interval of 1meter ± 1%.
The following information shall be marked on the outer sheath of the cable at an interval of about 1 meter.
Drum marking: Each side of every wooden drum shall be permanently marked in a minimum of 2.5~3 cm high lettering with the following:
ADSS Fiber Optic Cable Installation
Basically, the installation of ADSS optic cable is divided into two steps:
Step 1: Lay, arrange, and tighten the dielectric fiber optic cable and then install cable fittings and bridge molding.
Step 2: Fiber optic connection and characteristic test of the optic fiber.
The tips of ADSS fiber optic cable installation:
The straight-line distance from the tower to the cable laying equipment shall be greater than 4 times the height of the pulley suspension point to reduce the side pressure on the optic cable. Excessive tension shall not be used to pull the optic cable during cable laying, and the traction force shall not be greater than half of the initial tension borne by the optic cable. The traction speed of the optic cable is generally not greater than 20m/min.
在线联系供应商
Other supplier products
 |
Fiber Optic Cable & Fiber Optic Clamps | Optical cable is a communication line in which a certain number of optical fibers form a cable core, and are covered with sheathes to realize optic... |
 |
B Type 32 Port EDFA amplifer Fiber Optic Amplifiers (EDFA) | It's a 1550nm 32 port fiber outdoor optical amplifier(EDFA) with 23dbm output power. All installation accessory such as AC or DC power supply, SNMP... |
 |
LC Duplex Adapter | A fiber optic adapter, sometimes also called a coupler, is a small device designed to terminate or link the fiber optic cableor fiber optic connect... |
 |
Fiber Optic Cross Connect Cabinet | Fiber optic cross connectcabinet is a kind of transfer equipment that provides fiber optic cable terminations and patch cords for the backbone and ... |
 |
GYXTW Fiber Optic Cable | Fiber Optic GYXTW cableis to sheath 250μm optical fiber into a loose tube which is filled with waterproof compound. Water blocking material is a... |
Same products
 |
C500-1.7 Series High Flow Multi-Stage Centrifugal Blower /Centrifugal Blower | 卖方: Greentech International (Zhangqiu) Co., Ltd | Greentech International (Zhangqiu) Co., Ltdis the professional blower supplier.Multistage Centrif... |
 |
Common Rail injector control valve F00VC01303 | 卖方: China Lutong Part Plant | Common Rail injector control valve F00VC01303 Tina#Stainless Steel Cylindrical Pin##Denso Common... |
 |
Common Rail injector control valve F00VC01200 | 卖方: China Lutong Part Plant | Common Rail injector control valve F00VC01200 Tina#Stainless Steel Cylindrical Pin##Denso Common... |
 |
Injector Control Valve Plate 24# | 卖方: China Lutong Part Plant | Injector Control Valve Plate 24# Tina#Stainless Steel Cylindrical Pin##Denso Common Rail Injecto... |
 |
Injector Control Valve Plate 12# | 卖方: China Lutong Part Plant | Injector Control Valve Plate 12# Tina#Stainless Steel Cylindrical Pin##Denso Common Rail Injecto... |
