Tooth composite resin wear tester
Applicable standards:
YY/T 0113-2015 "Dental composite resin wear performance test method" : This standard specifies the test method of dental composite resin wear performance in detail, including the requirements of test equipment, test conditions, test steps and data processing. The design, manufacture and use of the tooth composite resin wear tester should strictly follow this standard to ensure the accuracy and reliability of the test results.
Main parameters:
Control system:
PLC （Programmable logic controller） control is used to realize the automatic control of the equipment.
Operation interface:
It is equipped with a color 7-inch touch screen and supports switching between Chinese and English for easy operation.
Wear movement mode:
The sample is moving in a circle with uniform speed and constant radius relative to the grinding part, and at the same time, it is moving in a vertical direction in an intermittent way.
The friction period is usually a 30 degree Angle.
The circular motion radius of the sample is 27.5mm.
The linear velocity at the center of the sample is 75mm/s.
Wear load:
Two loads, 22N and 172N, are included to simulate wear under different conditions.
Built-in balance:
It is equipped with an analytical balance with an accuracy of 0.0001g for the precise measurement of specimen wear.
Accessory:
For grinding: special rubber plate, the number is usually 20 pieces, diameter （100±1） mm, thickness （6±0.2） mm, Shore hardness 75±5HA.
Abrasive: In line with YB/T 5217-2005, grade FC-98, particle size 110 mesh ——120 mesh of fluorite concentrate, weight is usually 5kg.
Hair dryer: With a power of about 50W, it is used to clean abrasives and debris during the test.
Ultrasonic cleaning machine: the power is 400W, used for cleaning samples and grinding parts.
Sample mold: can prepare the diameter of （10±0.1） mm, high （6±0.5） mm sample mold, made of stainless steel material, easy to disassemble the sample.
Special fixture: used to fix the sample and the matching parts to ensure stability and accuracy during the test.
在线联系供应商
Other supplier products
 |
Programmable Temperature and Humidity Chamber | TRANSLATE with x English Arabic Hebrew Polish Bulgarian Hindi Portuguese Catalan Hmong Daw Romanian ... |
 |
UV Lamp Aging Test Tester | This product uses fluorescent UV lamps, combined with temperature and humidity device to simulate the material decline in color, brightness, streng... |
 |
Automobile wire cyclic bending testing machine | In terms of technical parameters: The swing angle can reach 180 degrees clockwise or counter - clockwise. It is also possible to continuously set a... |
 |
Downproof Tester | TRANSLATE with x English Arabic Hebrew Polish Bulgarian Hindi Portuguese Catalan Hmong Daw Romanian ... |
 |
Steel wheel wear testing machine | Product Introduction: The cycloidal pinwheel reducer has the advantages of large reduction ratio, compact structure, smooth transmission and adjus... |
Same products
 |
C500-1.7 Series High Flow Multi-Stage Centrifugal Blower /Centrifugal Blower | 卖方: Greentech International (Zhangqiu) Co., Ltd | Greentech International (Zhangqiu) Co., Ltdis the professional blower supplier.Multistage Centrif... |
 |
Common Rail injector control valve F00VC01303 | 卖方: China Lutong Part Plant | Common Rail injector control valve F00VC01303 Tina#Stainless Steel Cylindrical Pin##Denso Common... |
 |
Common Rail injector control valve F00VC01200 | 卖方: China Lutong Part Plant | Common Rail injector control valve F00VC01200 Tina#Stainless Steel Cylindrical Pin##Denso Common... |
 |
Injector Control Valve Plate 24# | 卖方: China Lutong Part Plant | Injector Control Valve Plate 24# Tina#Stainless Steel Cylindrical Pin##Denso Common Rail Injecto... |
 |
Injector Control Valve Plate 12# | 卖方: China Lutong Part Plant | Injector Control Valve Plate 12# Tina#Stainless Steel Cylindrical Pin##Denso Common Rail Injecto... |
