Hyper-durable powder coatings/non stick powder coating

Powder Properties

Appearance	Smooth Matt
Gloss level	20 – 30 gloss units (60°)
Particle size	Suitable for electrostatic spray
Specific gravity	1.2-1.7 g/cm³ depending on colour
Storage	Dry cool conditions below 25°C
Shelf life	6 months
Sales code	8 series
Stoving Schedule	30 – 40 minutes at 190°C or 20 – 30 minutes at 200°C or 15 – 25 minutes at 210°C (object temperature) Do not cure above 210°C

Mechanical Tests

Dry Adhesion	AAMA2605 8.4	Pass – no removal of film
Impact Resistance	AAMA2605 8.5	Pass – no tape removal of film from substrate following 3mm deformation
Dry Film Hardness	ISO2815 (Buchholz)	Pass
Abrasion Resistance	AAMA2605-13 8.6	Pass – abrasion coefficient >40

Pre-treatment

For maximum protection it is essential to pre-treat components prior to the application of MT- D3020 Gen II in accordance with the MT-D Approved Applicator Manual. Aluminium components must receive a full multi-stage chromate conversion coating or suitable chrome-free pre treatment to clean and condition the substrate. Detailed advice should be sought from the pre-treatment supplier.

Application – Cleanup

Below are some recommendations for minimising the risk of cross contamination of MT-D3020 Gen II with powders based on other chemistries such as polyester:

If possible, use a dedicated spray to waste booth if not reclaiming.

Ensure thorough cleaning of spray booth, duct work, cyclone (if within system) and all powder application equipment (guns, hoses, pumps, hoppers, etc) before and after applying MT-D3020 powders.

Clean wet rags should be used for a final wipe down on the inside of the booth and feed hopper.

When returning to application of polyester powders after a MT-D3020 run, shoot foam blocks through hoses and flush guns with next powder to remove any traces of fluorocarbon, and spray this powder to waste before reclaiming.

If reclaiming powder after MT-D3020 run, check reclaim powder for contamination before reuse.

Where possible isolate the application of MT-D3020 from other production eg. use at weekends or on night shift when no other production is taking place.

Other supplier products

	Powder coating series for vehicle compartment	Introduction With the development of environmental protection and energy conservation, the central environmental protection department and local g...
	Matte powder coating	Introduction Matte powder coating is a specialized type of coating that provides a non-reflective, low-gloss finish. It is applied as a dry powder...
	Purple powder coating-	Purple Powder Coating – Classification, Applications & Advantages ClassificationTypical ApplicationsProduct Advantages Glossy...
	High durability powder coatings MT-800	Product Description MT-800 is a series of high durability powder coatings designed for exterior exposure. Tested against the most severe specifica...
	Household electrical appliances powder coating	Brief description: Made of epoxy polyester mixed type, Primid polyester type, TGIC polyester type, etc. Features: ◆ Smooth surface effect ◆ Exc...

供应产品

Same products

	Hot Melt Adhesive for Vacuum Insulation Panels	卖方: Foshan Rurga New Material Technology Co. ,Ltd	Hot Melt Adhesive for Vacuum Insulation Panels Supply & Technical Support Capabilities ...
	Hot Melt Adhesive for Packaging	卖方: Foshan Rurga New Material Technology Co. ,Ltd	Hot Melt Adhesive for Packaging Bond Strength & Durability: Hot melt adhesives provide i...
	Hot Melt Adhesive for Hygiene Products	卖方: Foshan Rurga New Material Technology Co. ,Ltd	Hot Melt Adhesive for Hygiene Products refers to thermoplastic pressure‑sensitive adhesives ...
	LSAW Steel Pipe & Tube	卖方: HEBEI TIRICO PIPELINE CO.,LTD	LSAW Steel Pipe & Tube , or Longitudinal Submerged Arc-Welding Pipe (also known as SAWL ...
	Anti-Corrosion Steel Pipe & Tube	卖方: HEBEI TIRICO PIPELINE CO.,LTD	Anti-Corrosion Steel Pipe & Tube Anti-Corrosion Steel Pipe & Tube What Is an Anti...