CN089 SMT Wave Soldering Machine Lead Free 670KG Weight With PID Control

CNSMT 10 years production WAVE SOLDERING MACHINE after dip component
Feature
| P C Broad width | Board width | Max200mm |
| PCB conveyor height | PCB transportation height | 700±20mm |
| PCB conveyor speed | PCB transport speed | 0-1.8m/min |
| Preheating length | Preheat zone length | 400mm |
| Preheating Temperatures | Preheat zone temperature | Room temperature ~ 180 degrees |
| Suitable solder type | Suitable solder type | Lead-free solder, ordinary solder |
| Preheating capacity | Preheat power | 2KW |
| Wave solder pot | Wave soldering furnace power | 6KW |
| Solder volume | Solder tin capacity | Lead-free 120KG |
| Solder temperature | Tin furnace temperature | Room temperature ~300 degrees |
| Temperature control | Temperature control method | PID control, SSR drive |
| Flux storage tank | Flux capacity | Max5.2L |
| Power requirements | power supply | 3-phase or single-phase 220VAC |
| Power for heating up | Starting power | 8KW |
| Power for operation | Normal operating power | 2.0KW-2.5KW |
| Air supply | Gas source | 4-7kg/cm2 12.5L/min |
| Control fashion | Whole control method | PLC+ Meter/PLC+Touch Screen |
| Weight | weight | Max 350kg |
| Dimensions | Dimensions | L2200xW1100xH1500 |
Application
Wave soldering machine basic operating procedures
(Reference)
B1 wave soldering machine basic operating procedures
B1.1 Preparation
a. Check whether the wave soldering machine is equipped with ventilation equipment is good;
b. Check the wave soldering machine timing switch is good;
c. Check if the tin bath temperature indicator is normal.
Method: Adjust the temperature indicator up and down, and then use a thermometer to measure the temperature of the tin bath surface 10-15 mm, and determine whether the temperature changes with it:
d. Check whether the preheater system is normal.
Method: Turn on the pre-heater switch and check if it is warm and the temperature is normal.
e. Check the operation of the cutting knife.
Method: Adjust the height of the blade according to the thickness of the printed circuit board and the length of the remaining component lead. Then tighten and stabilize the blade holder, start the visual inspection of the rotation of the blade, and finally check the failure of the insurance device;
f. Check whether the supply of compressed air to the flux container is normal;
Method: Pour the flux, adjust the inlet valve, start the flux foam, use the sample board to adjust the foam to 1/2 of the plate thickness, and then tighten the IOP valve until the formal operation. Then move this valve, just open the air intake switch;
在线联系供应商
Other supplier products
| SMT Stick Feeder KXFW1KSRA00 For Panasonic CM602 Pcb Assembly Equipment | SMT Stick Feeder KXFW1KSRA00 Original New Use in Panasonic CM602 Pcb Assembly Equipment 8*2MM P / E M9A5NWM0000 double reel8*4MM P / E M9A1NWM0000 ... | |
| KHJ-MC500-000 Electronic Feeder , YS12 Yamaha Feeder 1 Year Warranty | KHJ-MC100-000 KHJ-MC100-003 YS KHJ-MC200-000 YAMAHA12/16mm SS12MM KHJ-MC400-000 KHJ-MC400-002 24MM KHJ-MC500-000 YAMAHA32mm KHJ-MC600-00... | |
| Surface Mounter SMT Feeder YAMAHA YV100XG CL12MM 16MM 1 Year Warranty | KHJ-MC40C-00 SEAL,MAIN LABEL 12 KHJ-MC132-00 SPROCKET 13 KHJ-MC23A-00 SHIM,SPROCKET 14 KHJ-MC43E-00 BOLT HEX.S/H LOW 15 KHJ-MC441-00 TAPE GUIDE ASS... | |
| SMT fuji Nozzle NXT XP142 XP141 XP243 XP241 ORIGINAL NOZZLE FOR FUJI pick and | SMT fuji Nozzle NXT XP142 XP141 XP243 XP241 ORIGINAL NOZZLE FOR FUJI pick and place mahcineFUJI CP742 CP743 CP842 DGPK0131 PLATEFUJI CP732 CP733 SH... | |
| KHY-M77A0-A0 SMT NOZZLE 310A YAMAHA YS12 YG12 YS24 pick and place machine | KHY-M1309-A1 COVER 9 ASSY. 1 (2008/12/2) MEX0091 OK2 KHY-M1309-10 COVER 9-1 1 (2008/12/2) MEX0091 OK3 KHY-M130A-02 COVER 9-2 1 (2008/12/2) MEX0091 ... |
Same products
| Hc-501s Low Noise Energy Saving Rotary Air Blower | 卖方: Greentech International (Zhangqiu) Co., Ltd | HC rotary air blower structure and working principleThe rotary blower has an exquisite structure ... | |
| Common Rail Injector Nozzle 880P119092 | 卖方: China lutong | Common Rail Injector Nozzle 880P119092 Common Rail Injector Nozzle A6510702887Chris Whats/ app:+... | |
| MIJING DY-11 FPC电源线,适用于iOS和Android设备测试 | 卖方: Phonefix | MiJing DY-11手机维修电源线采用iOS和Android FPC接口,专为iPhone 8/X/11/12/13/14/15 Pro Max、华为、小米、三星等手机设计。MiJing D... | |
| AI845 Analog Input Module 3BSE023675R1 | 卖方: 杭州颇菲科特科技有限公司 | General Information Product ID: 3BSE023675R1 Medium Description: AI845 Analog Input Module, 8 c... | |
| T9401 T9402 Digital Input Module | 卖方: 杭州颇菲科特科技有限公司 | The 9401 (8 channel) and 9402 (16 channel) are 24Vdc digital input modules. They accept galvanica... |










