High reliability walk-in heat aging chamber
Whats/App: +86 156 1874 6768
Web: standard-groups.com
Applications
Walk-in High-Temperature Aging Chambers are typically assembled on-site using insulated panels (double-sided color steel sheets with insulation material in between). Chamber dimensions are customized to client specifications. The complete walk-in high/low temperature and humidity test chamber features comprehensive safety protection devices and provides troubleshooting methods, with safety ratings surpassing other brands. Protection Devices: Fuse-less switches, fuses, over-temperature protection, dry-run protection, low-water protection, liquid level protection, compressor overpressure, overheat, and overcurrent protection. Comprehensive protection includes compressor overload/overheat protection, phase loss protection, and a fault alarm system.
Standards
GJB150.3 (ML-STD-810D) High Temperature Test Method
GJB150.4 (MIL-STD-810D) Low Temperature Test Method
GJB360.8-87 (MIL-STD-202f) High Temperature Life Test
GB/T5170.2-96 Temperature Test Equipment
GB2423.1-89 (IEC68-2-1) Basic Environmental Test Procedures for Electrical and Electronic Products Test A: Low Temperature Test Method
GB2423.2-89 (IEC68-2-2) Basic Environmental Test Procedures for Electrical and Electronic Products - Test B: High Temperature Test Method
GB5170. 2. 3. 5. 6-95 “Calibration Methods for Basic Parameters of Environmental Test Equipment for Electrical and Electronic Products - Low Temperature, High Temperature, Constant Humidity and Heat, Alternating Humidity and Heat Test Equipment” Requirements
Features
1. Simple maintenance and user-friendly operation are key advantages of our products.
2. The independent frame design ensures the refrigeration system and air distribution system operate separately.
3. Maintenance and repairs can be performed during unit operation, resulting in low annual failure rates and simplified, rapid servicing.
Parameters
| Item | Specifications |
|---|---|
| Dimensions | 200 cm (W) × 200 cm (H) × 200 cm (D); customizable per customer requirements, with external dimensions subject to actual size |
| Temperature Range | Optional ranges: 0°C~20°C / -40°C~60°C / -70°C~+85°C / 100°C (lower temperature ranges are higher in cost; choose based on product needs) |
| Temperature Fluctuation | ±0.5°C (defined as half the difference between the highest and lowest measured temperatures at the center point) |
| Temperature Uniformity | ±2.0°C (defined as the arithmetic mean of the differences between highest and lowest measured temperatures per test) |
| Heating Time | From room temperature (+10°C) to +85°C: <60 minutes, non-linear no-load heating rate ≈3°C/min |
| Cooling Time | - From +10°C to 0°C: <30 minutes, non-linear no-load cooling rate ≈1°C/min- From +10°C to -20°C: <45 minutes, non-linear no-load cooling rate ≈1°C/min- From +10°C to -40°C: <60 minutes, non-linear no-load cooling rate ≈1°C/min |
| Operating Noise | A-weighted sound level ≤60 dB(A), measured in anechoic chamber at 25°C ambient temperature, using A-weighting, averaged over 8 test points (each at 1m from noise source and 1m above ground) |
Test Procedures
1. Pre-Operation Preparation
Train personnel on safety procedures, emergency stop methods, and chamber operation.
Verify grounding and electrical system integrity; ensure voltage is within specifications (~380V).
Ensure adequate ventilation and unobstructed exhaust system.
Wear appropriate personal protective equipment (PPE) including heat-resistant gloves, safety shoes, and protective eyewear.
2. Sample Placement
Arrange test samples to avoid overcrowding and ensure uniform airflow.
Ensure sample weight and volume do not exceed chamber limits.
3. Operation
Set desired temperature and duration according to test protocol.
Start the chamber and monitor temperature via PID control system.
Check for abnormal readings or fluctuations; adjust settings as necessary.
4. Monitoring During Test
Continuously monitor internal temperature and airflow.
Inspect for leaks or abnormal fumes if using gas or electric heating.
Restrict access to authorized personnel only.
在线联系供应商
Other supplier products
 |
Automated Filter Integrity Tester | Whats/App: +86 156 1874 6768 Web: standard-groups.com Testing Standards ASTM F838 – Membrane bubble point method ASTM D5199 – Gas a... |
 |
Film Shrinkage Testing Machine | Whats/App: +86 156 1874 6768 Web: standard-groups.com Applications The film heat shrinkage rate tester is mainly used to test the heat shrinkage... |
 |
Nissan Scratch Tester Manufacturer | Automotive Interior Scratch Resistance Testing Machine | Get a quote： Whats/App: +86 156 1874 6768 Web: standard-groups.com Product Features Testing Modes Linear Scratch: Single-pass testing for coat... |
 |
Battery Cell Test Pressure Vessel，battery safety testing pressure chamber\ | Whats/App: +86 156 1874 6768 Web: standard-groups.com The Battery Cell Test Pressure Vessel is designed for thermal runaway testing of battery ce... |
 |
IEC 60335 Rice Cooker Button Life Test Machine Manufacturer China | Get a quote： Whats/App: +86 156 1874 6768 Web: standard-groups.com Standards (1) IEC 60335-1 Household and similar electrical appliances &ndash... |
Same products
 |
Cast Aluminum Lighting Base | 卖方: LianJiang Metals Company | Cast Aluminum Lighting Base is the perfect solution for combining structural stability with ... |
 |
Custom Cast Aluminium & Iron Casting Services | 卖方: LianJiang Metals Company | Custom Cast Aluminium & Iron Casting Services Custom Cast Aluminium & Iron Casting S... |
 |
Cast Aluminum Mailbox | 卖方: LianJiang Metals Company | Cast Aluminum Mailbox We can manufacture any for you, including cast aluminum mailbox part... |
 |
Cast aluminum and wrought aluminum | 卖方: LianJiang Metals Company | Cast aluminum and wrought aluminum Cast aluminum and wrought aluminum perform different fu... |
 |
PP Pickling Tank | 卖方: Hebei Annuo Automaiton Technology Co., Ltd. | PP Pickling Tank PP Pickling Tank — Polypropylene Pickling Tanks for Hot Dip Galvanizing ... |
