High reliability walk-in heat aging chamber

Whats/App: +86 156 1874 6768

Web: standard-groups.com

Applications

Walk-in High-Temperature Aging Chambers are typically assembled on-site using insulated panels (double-sided color steel sheets with insulation material in between). Chamber dimensions are customized to client specifications. The complete walk-in high/low temperature and humidity test chamber features comprehensive safety protection devices and provides troubleshooting methods, with safety ratings surpassing other brands. Protection Devices: Fuse-less switches, fuses, over-temperature protection, dry-run protection, low-water protection, liquid level protection, compressor overpressure, overheat, and overcurrent protection. Comprehensive protection includes compressor overload/overheat protection, phase loss protection, and a fault alarm system.

Standards

GJB150.3 (ML-STD-810D) High Temperature Test Method

GJB150.4 (MIL-STD-810D) Low Temperature Test Method

GJB360.8-87 (MIL-STD-202f) High Temperature Life Test

GB/T5170.2-96 Temperature Test Equipment

GB2423.1-89 (IEC68-2-1) Basic Environmental Test Procedures for Electrical and Electronic Products Test A: Low Temperature Test Method

GB2423.2-89 (IEC68-2-2) Basic Environmental Test Procedures for Electrical and Electronic Products - Test B: High Temperature Test Method

GB5170. 2. 3. 5. 6-95 “Calibration Methods for Basic Parameters of Environmental Test Equipment for Electrical and Electronic Products - Low Temperature, High Temperature, Constant Humidity and Heat, Alternating Humidity and Heat Test Equipment” Requirements

Features

1. Simple maintenance and user-friendly operation are key advantages of our products.

2. The independent frame design ensures the refrigeration system and air distribution system operate separately.

3. Maintenance and repairs can be performed during unit operation, resulting in low annual failure rates and simplified, rapid servicing.

Parameters

Item	Specifications
Dimensions	200 cm (W) × 200 cm (H) × 200 cm (D); customizable per customer requirements, with external dimensions subject to actual size
Temperature Range	Optional ranges: 0°C~20°C / -40°C~60°C / -70°C~+85°C / 100°C (lower temperature ranges are higher in cost; choose based on product needs)
Temperature Fluctuation	±0.5°C (defined as half the difference between the highest and lowest measured temperatures at the center point)
Temperature Uniformity	±2.0°C (defined as the arithmetic mean of the differences between highest and lowest measured temperatures per test)
Heating Time	From room temperature (+10°C) to +85°C: <60 minutes, non-linear no-load heating rate ≈3°C/min
Cooling Time	- From +10°C to 0°C: <30 minutes, non-linear no-load cooling rate ≈1°C/min- From +10°C to -20°C: <45 minutes, non-linear no-load cooling rate ≈1°C/min- From +10°C to -40°C: <60 minutes, non-linear no-load cooling rate ≈1°C/min
Operating Noise	A-weighted sound level ≤60 dB(A), measured in anechoic chamber at 25°C ambient temperature, using A-weighting, averaged over 8 test points (each at 1m from noise source and 1m above ground)

Test Procedures

1. Pre-Operation Preparation

Train personnel on safety procedures, emergency stop methods, and chamber operation.

Verify grounding and electrical system integrity; ensure voltage is within specifications (~380V).

Ensure adequate ventilation and unobstructed exhaust system.

Wear appropriate personal protective equipment (PPE) including heat-resistant gloves, safety shoes, and protective eyewear.

2. Sample Placement

Arrange test samples to avoid overcrowding and ensure uniform airflow.

Ensure sample weight and volume do not exceed chamber limits.

3. Operation

Set desired temperature and duration according to test protocol.

Start the chamber and monitor temperature via PID control system.

Check for abnormal readings or fluctuations; adjust settings as necessary.

4. Monitoring During Test

Continuously monitor internal temperature and airflow.

Inspect for leaks or abnormal fumes if using gas or electric heating.

Restrict access to authorized personnel only.

Другие товары поставщика

	Automotive Wire Insulation Manual Bend Test System Factory Direct	Get a quote： Whats/App: +86 156 1874 6768 Web: standard-groups.com Parameters ParameterSpecification Clamp Type Manual Clamp S...
	Dual-Station Motorized Crocking Tester	Whats/App: +86 156 1874 6768 Web: standard-groups.com The Dual-Station Motorized Crocking Tester is designed to evaluate the color fastness of te...
	EN ISO 20344 water vapour permeability tester	Get a quote： Whats/App: +86 156 1874 6768 Web: standard-groups.com The Leather Water Vapor Permeability Tester measures the ability of leather a...
	Battery combustion tester	Whats/App: +86 156 1874 6768 Web: standard-groups.com The Battery Combustion Tester is designed for safety evaluation of lithium-ion batteries by...
	Scratch resistance test equipment	Whats/App: +86 156 1874 6768 Web: standard-groups.com Application The Scratch Resistance Test Machine is suitable for a wide range of materials ...

Все товары поставщика

Похожие товары

	PP Pickling Tank	Продавец: Hebei Annuo Automaiton Technology Co., Ltd.	PP Pickling Tank PP Pickling Tank — Polypropylene Pickling Tanks for Hot Dip Galvanizing ...
	Galvanizing Tank/Galvanizing Kettle/Zinc Kettle	Продавец: Hebei Annuo Automaiton Technology Co., Ltd.	Galvanizing Tank/Galvanizing Kettle/Zinc Kettle Zinc Kettle / Galvanized Kettle for Hot-Dip Galv...
	Galvanizing Furnace	Продавец: Hebei Annuo Automaiton Technology Co., Ltd.	Galvanizing Furnace Hot Dip Galvanizing Furnace Manufacturer— Engineered for Your Producti...
	Flue Gas Heat Economizer waste heat recovery	Продавец: Hebei Annuo Automaiton Technology Co., Ltd.	Flue Gas Heat Economizer waste heat recovery Flue Gas Heat Economizer – Waste Heat Recover...
	Granite Tanks	Продавец: Hebei Annuo Automaiton Technology Co., Ltd.	Granite Tanks Granite Tank — Granite Pickling Tank for Hot Dip Galvanizing The granite ta...