Plastic Biodegradation Testing System，ISO 16929 Biodegradable Plastic Testing Instruments
Whats/App: +86 156 1874 6768
Web: standard-groups.com
The Plastic Biodegradation Testing System is a laboratory system used to evaluate the ultimate aerobic biodegradation performance and disintegration behavior of plastic materials under controlled composting conditions. By continuously measuring the carbon dioxide released during aerobic biodegradation, you can accurately determine the biodegradation percentage and material disintegration performance.
Application
You use this system to assess the biodegradability of plastic and bio-based materials under controlled composting environments.
It is suitable for testing biodegradable plastics, compostable plastics, bio-based polymer materials, packaging materials, agricultural films, shopping bags, polyester-based biodegradable plastics, and other polymer products intended for composting or environmental degradation evaluation.
Standards
The Plastic Biodegradation Testing System complies with and supports testing according to the following standards:
(1) GB/T 19277.1-2011 Determination of the ultimate aerobic biodegradability of materials under controlled composting conditions – Method by analysis of released carbon dioxide – Part 1: General method
(2) GB/T 19277.2-2013 Determination of the ultimate aerobic biodegradability of materials under controlled composting conditions – Method by analysis of released carbon dioxide – Part 2: Gravimetric determination of carbon dioxide released under laboratory conditions
(3) GB/T 19811-2005 Determination of the degree of disintegration of plastic materials under defined composting conditions
(4) ISO 16929:2021 Plastics – Determination of the degree of disintegration of plastic materials under defined composting conditions in a pilot-scale test
(5) GB/T 29649-2013 Determination of bio-based content in bio-based materials – Liquid scintillation counting method
(6) GB/T 33797-2017 Determination of the ultimate anaerobic biodegradability of plastics under high-solids composting conditions by analysis of released biogas
(7) GB/T 22047-2008 Determination of the ultimate aerobic biodegradability of plastic materials in soil by measuring oxygen demand or released carbon dioxide
(8) GB/T 20197-2006 Degradable plastics – Definition, classification, marking and degradability requirements
(9) GB/T 32163.2-2015 Ecodesign product assessment specification – Part 2: Degradable plastics
(10) GB/T 16716.7-2012 Packaging and packaging waste – Part 7: Biodegradation and composting
(11) GB/T 38082-2019 Biodegradable plastic shopping bags
(12) GB/T 29646-2013 Modified polyester biodegradable plastics for blow molding films
(13) GB/T 32366-2015 Biodegradable poly(butylene adipate-co-terephthalate) (PBAT)
(14) GB/T 33798-2017 Biodegradable polyester roll bags
(15) GB/T 35795-2017 Fully biodegradable agricultural mulch films
Parameters
| Item | Description |
|---|---|
| Test Method | Aerobic composting biodegradation |
| Composting Mode | Static composting vessel |
| Measured Indicator | Carbon dioxide (CO₂) release |
| Evaluation Results | Biodegradation percentage, disintegration degree |
| Test Environment | Controlled temperature, oxygen concentration, and humidity |
| Carbon Source Analysis | Total Organic Carbon (TOC) |
| Monitoring Method | Continuous monitoring and periodic measurement |
| Blank Control | Blank composting vessel included |
Features
You can determine the ultimate aerobic biodegradation capability of plastic materials through precise CO₂ monitoring.
The system simulates controlled composting conditions with regulated temperature, oxygen, and humidity.
Biodegradation percentage is calculated by comparing actual CO₂ release with theoretical CO₂ based on TOC.
The system allows evaluation of both biodegradation performance and material disintegration at the end of the test.
It supports reliable comparison between test samples and blank controls.
Accessories
(1) Static composting vessels
(2) Carbon dioxide collection and measurement units
(3) Temperature and humidity control components
(4) Oxygen concentration control components
(5) Sample mixing and inoculation tools
Test Procedures
You mix the test material with inoculum and load it into the composting vessel.
The mixture undergoes aerobic composting under specified temperature, oxygen concentration, and humidity.
Carbon dioxide released from both test and blank vessels is continuously monitored and periodically measured.
You calculate cumulative CO₂ release and determine the biodegradation percentage based on theoretical values.
At the end of the test, you assess material disintegration and mass loss if required.
Maintenance Information
You should regularly check gas collection and measurement components for sealing and accuracy.
Composting vessels must be cleaned after each test cycle to prevent cross-contamination.
Sensors and control systems should be calibrated periodically according to laboratory requirements.
All components should be maintained to ensure stable long-term operation.
在线联系供应商
Other supplier products
 |
Multiphase High - temperature and High - pressure Explosion Limit Tester | Whats/App: +86 156 1874 6768 Web: standard-groups.com Reference Standards: EN 1839 ASTM E918 ASTM E2079 EN 15967 UL9540A Product Features: 1. ... |
 |
High Precision Nissan 4-Station Abrasion Tester | Get a quote： Whats/App: +86 156 1874 6768 Web: standard-groups.com Features (1) Independent 4-station design reduces testing time by up to 75% ... |
 |
Custom wide-range load friction and wear testing equipment | Whats/App: +86 156 1874 6768 Web: standard-groups.com Application This testing machine is suitable for a wide range of friction and wear evaluat... |
 |
Flooring Radiant Panel Test Apparatus EN ISO 9239-1 | Whats/App: +86 156 1874 6768 Web: standard-groups.com The Flooring Radiant Panel Test Apparatus is used to tester a variety of flooring materials... |
 |
Standard light source sample table | Whats/App: +86 156 1874 6768 Web: standard-groups.com Standards ISO 3664:2009: Meets international standards for graphic arts and photography vi... |
Same products
 |
HDPE高速水冷双壁波纹管生产线 | 卖方: Shandong HUASU Plastic Technology Co.,Ltd. | 机头模具采用双流道结构、氮化磨光处理机头，偏壁调整方便快捷，保证内外层壁厚均匀和稳定成型。 最新设计密闭压力水冷冷却结构，冷却充分，多点分布真空系统，效率更高，生产速度更快。 双层在线扩口功... |
 |
PanEVAP & MVR system | 卖方: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd | A multiple-effect evaporator is a device that efficiently uses steam heat to evaporate water. Wat... |
 |
PanGAP wide gap welded plate heat exchanger | 卖方: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd | PanGAP wide gap welded plate heat exchangerconsists of a welded plate pack with different channel... |
 |
PanBloc welded plate heat exchanger | 卖方: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd | PanBloc welded plate heat exchangeris compact and efficient, although fully welded, is totally ac... |
 |
PanBox welded plate heat exchanger | 卖方: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd | PanBox welded plate heat exchangerconsists of a laser welded plate pack with optimized corrugated... |
