Plastic Biodegradation Testing System，ISO 16929 Biodegradable Plastic Testing Instruments
Whats/App: +86 156 1874 6768
Web: standard-groups.com
The Plastic Biodegradation Testing System is a laboratory system used to evaluate the ultimate aerobic biodegradation performance and disintegration behavior of plastic materials under controlled composting conditions. By continuously measuring the carbon dioxide released during aerobic biodegradation, you can accurately determine the biodegradation percentage and material disintegration performance.
Application
You use this system to assess the biodegradability of plastic and bio-based materials under controlled composting environments.
It is suitable for testing biodegradable plastics, compostable plastics, bio-based polymer materials, packaging materials, agricultural films, shopping bags, polyester-based biodegradable plastics, and other polymer products intended for composting or environmental degradation evaluation.
Standards
The Plastic Biodegradation Testing System complies with and supports testing according to the following standards:
(1) GB/T 19277.1-2011 Determination of the ultimate aerobic biodegradability of materials under controlled composting conditions – Method by analysis of released carbon dioxide – Part 1: General method
(2) GB/T 19277.2-2013 Determination of the ultimate aerobic biodegradability of materials under controlled composting conditions – Method by analysis of released carbon dioxide – Part 2: Gravimetric determination of carbon dioxide released under laboratory conditions
(3) GB/T 19811-2005 Determination of the degree of disintegration of plastic materials under defined composting conditions
(4) ISO 16929:2021 Plastics – Determination of the degree of disintegration of plastic materials under defined composting conditions in a pilot-scale test
(5) GB/T 29649-2013 Determination of bio-based content in bio-based materials – Liquid scintillation counting method
(6) GB/T 33797-2017 Determination of the ultimate anaerobic biodegradability of plastics under high-solids composting conditions by analysis of released biogas
(7) GB/T 22047-2008 Determination of the ultimate aerobic biodegradability of plastic materials in soil by measuring oxygen demand or released carbon dioxide
(8) GB/T 20197-2006 Degradable plastics – Definition, classification, marking and degradability requirements
(9) GB/T 32163.2-2015 Ecodesign product assessment specification – Part 2: Degradable plastics
(10) GB/T 16716.7-2012 Packaging and packaging waste – Part 7: Biodegradation and composting
(11) GB/T 38082-2019 Biodegradable plastic shopping bags
(12) GB/T 29646-2013 Modified polyester biodegradable plastics for blow molding films
(13) GB/T 32366-2015 Biodegradable poly(butylene adipate-co-terephthalate) (PBAT)
(14) GB/T 33798-2017 Biodegradable polyester roll bags
(15) GB/T 35795-2017 Fully biodegradable agricultural mulch films
Parameters
| Item | Description |
|---|---|
| Test Method | Aerobic composting biodegradation |
| Composting Mode | Static composting vessel |
| Measured Indicator | Carbon dioxide (CO₂) release |
| Evaluation Results | Biodegradation percentage, disintegration degree |
| Test Environment | Controlled temperature, oxygen concentration, and humidity |
| Carbon Source Analysis | Total Organic Carbon (TOC) |
| Monitoring Method | Continuous monitoring and periodic measurement |
| Blank Control | Blank composting vessel included |
Features
You can determine the ultimate aerobic biodegradation capability of plastic materials through precise CO₂ monitoring.
The system simulates controlled composting conditions with regulated temperature, oxygen, and humidity.
Biodegradation percentage is calculated by comparing actual CO₂ release with theoretical CO₂ based on TOC.
The system allows evaluation of both biodegradation performance and material disintegration at the end of the test.
It supports reliable comparison between test samples and blank controls.
Accessories
(1) Static composting vessels
(2) Carbon dioxide collection and measurement units
(3) Temperature and humidity control components
(4) Oxygen concentration control components
(5) Sample mixing and inoculation tools
Test Procedures
You mix the test material with inoculum and load it into the composting vessel.
The mixture undergoes aerobic composting under specified temperature, oxygen concentration, and humidity.
Carbon dioxide released from both test and blank vessels is continuously monitored and periodically measured.
You calculate cumulative CO₂ release and determine the biodegradation percentage based on theoretical values.
At the end of the test, you assess material disintegration and mass loss if required.
Maintenance Information
You should regularly check gas collection and measurement components for sealing and accuracy.
Composting vessels must be cleaned after each test cycle to prevent cross-contamination.
Sensors and control systems should be calibrated periodically according to laboratory requirements.
All components should be maintained to ensure stable long-term operation.
Send product request
Other supplier products
 |
Nonwoven Water Absorption Tester | Get a quote： Whats/App: +86 156 1874 6768 Web: standard-groups.com Fabric Water Absorption Tester is designed to test the ability of terry fabri... |
 |
Battery Powder Compaction Density Evaluation System | Whats/App: +86 156 1874 6768 Web: standard-groups.com Application (1) Measurement of tapped density and compaction characteristics of lithium-io... |
 |
Laboratory gas pulsation tester for industrial applications | Whats/App: +86 156 1874 6768 Web: standard-groups.com Standards The system supports compliance with major automotive engineering standards: GMW... |
 |
Four - point Bending Tester | Whats/App: +86 156 1874 6768 Web: standard-groups.com Standard YY/T 0342-2022: Chinese standard specifying methods for determining bending stren... |
 |
Oxidizing liquid time pressure tester | Whats/App: +86 156 1874 6768 Web: standard-groups.com Conforms to UN Recommendations on the Transport of Dangerous Goods - Manual of Tests and Cr... |
Same products
 |
Laser Cutting Machines | Seller: Chanxan (Changshu) Laser Technology Co., Ltd. | Laser Cutting Machines PrecisionLaser Cutting Systemsfor Film, Glass & Industrial Materials ... |
 |
Precision Laser Micromachining Machine | Seller: Chanxan (Changshu) Laser Technology Co., Ltd. | Precision Laser Micromachining Machine| Ultrafast Laser Micromachining Systems Chanxan provides ... |
 |
Ultrafast Laser Systems | Seller: Chanxan (Changshu) Laser Technology Co., Ltd. | Ultrafast Laser Systems Femtosecond Laser System Ultra-precision femtosecond laser systemfor hi... |
 |
Industrial Laser Equipment Manufacturer | Seller: Chanxan (Changshu) Laser Technology Co., Ltd. | Industrial Laser Equipment Manufacturer for Precision Cutting, Marking & Micromachining Chan... |
 |
Common Rail Injector Valve F00R J02 012 | Seller: 868983 | Common Rail Injector Valve F00R J02 012 David Chen |
