Transmission Fluid Friction Tester
Whats/App: +86 156 1874 6768
Web: standard-groups.com
The Passenger Vehicle Automatic Transmission Fluid Anti-Shudder Friction Tester is a specialized friction testing system designed to evaluate the friction characteristics and anti-shudder durability of automatic transmission fluids (ATF) under controlled pressure, speed, and temperature conditions.You can use this tester to accurately simulate the real operating conditions of wet friction pairs in automatic transmissions, enabling quantitative analysis of friction behavior during running-in, low-speed operation, and long-term durability. It provides reliable technical support for lubricant development, quality control, and compliance verification.
Standards
The tester is designed to meet and support the following domestic and international standards and test methods:
(1) GB/T 11118 — Tribological Performance Test Methods for Lubricants
(2) GB/T 3142 — General Test Methods for Lubricant Viscosity and Performance
(3) JASO M348 — Friction Characteristics Test Method for Automatic Transmission Fluids
(4) SAE No.2 — Friction Test Method for Automatic Transmission Fluids
Note: Differences in speed profiles, loading modes, temperature programs, and data processing requirements among standards can be accommodated through software parameter configuration.
Parameters
| Category | Parameter | Technical Specification | Remarks |
|---|---|---|---|
| Load system | Axial load range | 200 N – 10.000 N | Servo-hydraulic loading |
| Load indication relative error | ±0.5% | ||
| Long-term load holding error | ±0.05 MPa | ||
| Stroke | Axial loading stroke | 150 mm | |
| Friction measurement | Maximum friction torque | 320 N·m | |
| Friction torque relative error | ±2% | ||
| Drive system | Sliding speed range | 0.01 – 1.5 m/s | Continuously adjustable |
| Speed control accuracy | ±0.01 m/s | ||
| Drive motor | 380 V / 11 kW | AC servo motor | |
| Temperature control | Temperature range | –30 °C to 200 °C | Indirect heating & cooling |
| Temperature control accuracy | ±2 °C | ||
| Heating power | 220 V / 300 W | ||
| Cooling power | 220 V / 2.37 kW | ||
| System power | Total power | 16.5 kW | Including load, drive, temperature |
| Control & monitoring | Time setting range | 1 s – 9999 min | |
| Real-time monitored parameters | Load, friction force, speed, temperature, time |
Accessories
(1) Friction plate fixture for standard friction plate sizes
(2) Steel plate fixture compliant with JASO and SAE requirements
(3) Servo-hydraulic axial loading unit
(4) Temperature-controlled oil bath with heating and cooling
(5) Industrial all-in-one computer with control and analysis software
(6) Sealing components for routine replacement
(7) Operation manual
Test Procedures
(1) Install the friction plate and steel plate with proper coaxial alignment
(2) Fill the test chamber with the specified volume of transmission fluid
(3) Perform the running-in stage according to the selected standard
(4) Execute μ–V characteristic tests using defined speed steps
(5) Conduct durability cycling tests to monitor friction coefficient evolution
(6) Stop the test automatically upon completion of the programmed cycle
(7) Remove samples and inspect wear condition
(8) Generate test curves and reports using the software system
Maintenance Information
(1) Check fixture alignment before each test to prevent eccentric loading
(2) Set running-in and test parameters strictly according to the applicable standard
(3) Do not exceed the specified axial load and temperature limits
(4) Allow natural cooling after high-temperature tests before disassembly
(5) Regularly calibrate load, speed, and temperature sensors
(6) Replace sealing components periodically to ensure system reliability
在线联系供应商
Other supplier products
 |
Resistance Tester for Molten Metal Droplet (Splash) Impact Performance | Whats/App: +86 156 1874 6768 Web: standard-groups.com Performance and Standards: This resistance tester for molten metal droplet (splash) impact... |
 |
Automatic freezing point pour point cold tester | Whats/App: +86 156 1874 6768 Web: standard-groups.com Product Introduction: The automatic freezing point pouring point Freezing point tester is ... |
 |
ISO paper flammability test equipment | Get a quote： Whats/App: +86 156 1874 6768 Web: standard-groups.com The flame-retardant paper and cardboard combustion tester is suitable for tes... |
 |
Sharp edge tester | Whats/App: +86 156 1874 6768 Web: standard-groups.com Standards : ASTM F963 4.8. EN71-1998 8.14. GB6675-2003 A.5.9. 16CFR 1500.48 Basic Configu... |
 |
Nissan interior material scratch tester | Whats/App: +86 156 1874 6768 Web: standard-groups.com The Scratch Tester is designed to evaluate the scratch resistance of materials such as auto... |
Same products
 |
MMA-120 Handheld Arc Welder | 卖方: 871183 | The MMA-120 Handheld Arc Welder from ChuangLi Electronic Technology Co., Ltd. is designed for con... |
 |
SHX Series Circulating Fluidized Bed Steam Boiler | 卖方: Hebei Genjux Boiler Co.,Ltd | Capacity: 10-35 t/hWorking pressure: 1.25-2.5 MPaOperating temperature: 194-400 ℃Applicable to bi... |
 |
YQ(Y)W Series Oil/Gas Fired Vertical Thermal Oil Boiler | 卖方: Hebei Genjux Boiler Co.,Ltd | Capacity: 7000-29200 KWOperating pressure: 0.8-1.0 MPaOperating temperature: 320℃Operating mode: ... |
 |
DHL Series Coal-Fired Steam Boilers | 卖方: Hebei Genjux Boiler Co.,Ltd | Capacity: 35-75 t/hOperating pressure: 1.25-5.4 MPaOperating temperature: 194-485℃Applicable to b... |
 |
SZL Series Biomass Steam Boiler | 卖方: Hebei Genjux Boiler Co.,Ltd | Capacity: 6-35 t/hWorking pressure: 1.0-2.5 MPaOperating temperature: 184-350 ℃Applicable fuel bi... |
