Building Material Fire Endurance Test Furnace OEM Manufacturer

Get a quote：

Whats/App: +86 156 1874 6768

Web: standard-groups.com

Features

The furnace incorporates advanced design and control technology to ensure stable, accurate, and repeatable testing.

Control System

Touchscreen and PC dual-control interface

Wireless connection supported; one PC can manage multiple furnaces

Automatic elimination of faulty thermocouples to maintain curve accuracy

Testing Performance

Full-automatic testing process from ignition to cooling

Real-time tracking of temperature and pressure curves

Automatic re-ignition if the flame is extinguished during testing

Automatic stop when reaching preset temperature or test duration

Safety and Reliability

Anti-power-off protection mode to avoid damage caused by sudden shutdown

Automatic cooling and exhaust system at the end of the test

Temperature deviation consistently lower than the limits required by GB standards

Data Management

Storage capacity for more than 100 sets of test data

Curve display for furnace temperature, back-surface temperature, and pressure

User-friendly interface for on-site operation or remote control

Parameters

Item	Specification
Working Voltage	AC 220V ± 10%, 50 Hz
Power Consumption	3 kW
Furnace Pressure Range	0–100 Pa
Pressure Control Accuracy	20 ± 3 Pa
Airflow Range	0–50 m³/min
Airflow Accuracy	≤ ±0.5 m³/min
Fuel Type	0# or −10# diesel
Standard Fire-Curve Temperature Program	60 min: RT–925°C; 120 min: RT–1050°C; 180 min: RT–1115°C; 240 min: RT–1150°C; 300 min: RT–1180°C; 360 min: RT–1210°C
Furnace Temperature Sensors	4 pcs K-type armored thermocouples
Back-Surface Temperature Sensors	2 pcs, accuracy ±4°C
Temperature Control Mode	Average or independent control
Heating Mode	Fully automatic diesel spray burner
Cooling Mode	Automatic exhaust and cooling
Timing Range	0–360 min
Data Storage Capacity	≥100 sets
Sample Size	500 × 500 × 6 mm
Overall Dimensions	1.6 m × 1.6 m × 1.6 m

Test Procedures

1. Cut the sample using a 250mm × 90mm template. If the sample is a melt-shrinkable product, use a 250mm × 180mm template.

2. Clamp the sample in a 250mm × 90mm sample holder, tighten the wing nut, and secure the sample. The sample holder size for melt-shrinkable products is 250mm × 180mm. At this point, do not yet mount the sample holder onto the horizontal rod.

3. Turn on the power switch and set the ignition time to a slightly longer duration, such as 5 minutes. Select the appropriate positioning device according to the ignition method. After pressing "Start Test" and the burner stops at the 45° position, insert one end of the positioning device into the burner. Now mount the sample holder onto the horizontal rod and adjust the sample holder's up, down, left, and right positions to meet the test requirements. Remove the positioning device. Press the return key. After the burner resets, press "Test Reset".

4. Press and hold the ignition button, and simultaneously adjust the flame adjustment valve on the instrument panel. After igniting the gas, adjust the flame height to 20 ± 1mm. When adjusting the flame from large to small, it is easier to first tighten the flame adjustment knob on the panel. The height gauge should be at 20mm. Close the front door.

5. Place two pieces of filter paper in the collection tray and then place it under the sample.

6. Set the ignition time, press "Start Test," and the burner will automatically rotate to the 45° position and remain there for the set ignition time, then reset. The afterglow time starts counting simultaneously. If the sample stops afterglow before reaching the marked line, press "Stop Afterglow." If the sample afterglow reaches the marked line, immediately press "Stop Afterglow." Record the burning time.

7. Press "Test Reset" to stop the test. To continue the test, repeat the above steps; otherwise, turn off the power. Provided by Shandong Provincial Textile Science Research Institute.

Other supplier products

	Tensile and Shear Tester STD - FB1 - A	Whats/App: +86 156 1874 6768 Web: standard-groups.com The Tensile and Shear Tester analyzes hand movements-referred to as "tensile"and "shear"-pe...
	DIN 71460 Filter Test System	Whats/App: +86 156 1874 6768 Web: standard-groups.com Application You can use this system for: Quality Control: Verify the performance of fuel ...
	Plastic Friction and Wear Tester	Whats/App: +86 156 1874 6768 Web: standard-groups.com Product Description: Plastic sliding friction wear tester consists of two main parts: the ...
	Medical infusion set leakage testing equipment	Whats/App: +86 156 1874 6768 Web: standard-groups.com Application This tester is designed for positive pressure leakage testing of medical infus...
	Glove Cut Resistance Tester	Whats/App: +86 156 1874 6768 Web: standard-groups.com Product Introduction: The machine is used to test the cutting resistance of gloves. Under ...

供应产品

Same products

	不锈钢焊剂芯焊丝 E308T1-1 E308HT1-1 E308LT1-1 用于304不锈钢焊接的气保焊丝	卖方: 863048	产品描述 不锈钢药芯焊丝 E308T1-1 E308HT1-1 E308LT1-1，FCAW不锈钢焊丝，AWS A5.22药芯焊丝，304不锈钢焊接耗材，低碳不锈钢药芯焊丝，耐高温不锈钢焊丝，...
	E317LT1-1 焊剂芯线 CO2 不锈钢焊剂含量70% 直径1.0/1.2/1.6mm OEM定制 1200℃熔点	卖方: 863048	迅卓不锈钢药心焊丝 E317LT1-1 分类： Сварочная проволока E317LT1-1 с флюсом, нержавеющая сталь, 70% содержан...
	Mini Jewelry Laser Repair System – 60W to 400W Precision Welding	卖方: Beijing JCZ Technology Co., Ltd	The Mini Jewelry Laser Welding Machineis an advanced mini laser welding system engineered for pre...
	Portable Backpack Laser Cleaning Machine – Lightweight, Efficient Rust & Paint Removal	卖方: Beijing JCZ Technology Co., Ltd	TheHCP-M SeriesBackpack Laser Cleaning Machinefeatures a compact pulsed fiber laser system, desig...
	Suitcase Pulsed Laser Cleaning Machine | Ultra-Portable Handheld Fiber Laser Cleaner	卖方: Beijing JCZ Technology Co., Ltd	The Suitcase Pulsed Laser Cleaning Machineis an ultra-portable, high-precision handheld fiber las...