Rubber hose outer coating wear testing machine
The Rubber Hose Outer Coating Wear Testing Machine is a precision laboratory and production testing instrument designed to evaluate the abrasion resistance of rubber and thermoplastic hose outer coatings. It is suitable for hoses reinforced with fabric or steel wire and featuring smooth, flat surfaces. By applying a controlled reciprocating motion with a defined vertical load, this machine simulates real-world wear conditions experienced by hydraulic, automotive, and industrial hoses, providing accurate and reproducible data for quality control, R&D, and material performance evaluation.
Applications
(1) Hydraulic hoses: Rubber hoses with smooth, flat outer coatings reinforced with fabric or steel wire.
(2) Industrial hoses: Air, water, and chemical hoses with similar outer coating structures.
(3) Automotive hoses: Brake lines, fuel lines, and coolant hoses.
(4) Testing laboratories: Quality control and research for abrasion resistance of hose coatings.
(5) Material evaluation: Suitable for rubber, thermoplastic, or composite hose cladding.
Standards
(1) GB/T 12721-2007 — Determination of abrasion resistance of rubber hose outer coating
(2) ISO 6945:1991 — Rubber hoses — Determination of abrasion resistance of cladding
(3) KS M ISO 6945-2013 — Determination of abrasion resistance of the outer coating of rubber hoses
(4) EN ISO 6945-1996 — Determination of abrasion resistance of rubber hose outer coatings
(5) DS/ISO 6945-1984 — Determination of wear resistance of rubber hose cladding
Features
(1) High reproducibility: Provides consistent and accurate abrasion testing of rubber hose outer coatings.
(2) Versatile mandrel sizes: Supports a wide range of shaft diameters to accommodate different hose types.
(3) Adjustable load: Vertical static pressure can be set according to the product standard or customized.
(4) Simulates real-world wear: Reciprocating motion reproduces the friction and wear that hoses experience in operation.
(5) Easy operation and setup: Simple installation of hose samples and abrasive tool ensures quick test preparation.
Technical Parameters
| Item | Specification |
|---|---|
| Reciprocating frequency | 1.25 Hz (45 RPM) |
| Cycle stroke | 200 mm |
| Loading static pressure | 50 N ± 0.5 N (customizable) |
| Mandrel length | 150 mm |
| Shaft diameters | 5, 8, 10, 13, 16, 19, 22, 25, 32, 38, 45, 51 mm (3 selectable, or customized) |
| Power supply | AC 220V, 50/60 Hz (typical) |
Accessories
(1) Main testing machine ×1
(2) Standard mandrels (3 selectable sizes) ×1 set
(3) Abrasive tool ×1
(4) Weights for loading pressure ×1 set
(5) Power cable ×1
(6) Instruction manual ×1
Test Procedure
(1) Install the assembled hose sample and mandrel on the test device, ensuring no axial movement or rotation.
(2) Position the abrasive tool in contact with the sample and apply the vertical static pressure F specified by the standard (or 50 N ± 0.5 N if unspecified).
(3) Start the machine and allow it to run until the required number of cycles is completed.
(4) Remove the sample assembly, clean off any debris or particles from the outer coating, and weigh the sample (with or without core shaft) to compare with initial weight.
Maintenance Information
(1) Regularly clean the abrasive tool and test mandrels to remove rubber debris.
(2) Inspect the reciprocating mechanism and bearings periodically for smooth operation.
(3) Check calibration of applied load weights to ensure consistent static pressure.
(4) Lubricate moving parts according to the manufacturer’s recommendations.
(5) Store the machine in a clean, dry environment when not in use.
在线联系供应商
Other supplier products
 |
Minimum Ignition Temperature (MIT) – Dust Cloud Tester | Dust Cloud Minimum Ignition Temperature Tester is mainly used to assess the explosiveness of dust in the production and processing places such as a... |
 |
Full Notch Creep Tester | This testing machine is used to test the environmental stress cracking performance of plastic materials. The equipment features touchscreen operati... |
 |
Prefilled Syringe Plunger Force Tester | The Prefilled Syringe Plunger Force Tester is widely used in the medical device industry, mainly for testing the push - force performance of prefil... |
 |
Gloss Meter | Standard The SpectroColor Pro S Series Gloss Meter adheres to stringent automotive interior quality control standards, includingISO 2813. ASTM D52... |
 |
Cork Puncture and Chip Detection Instrument | The rubber stopper puncture debris detector is a device specifically used to detect the number of debris generated during the puncture process and ... |
Same products
 |
Air Permeability Tester STD- F8 | 卖方: Standard International Group (HK) Limited | The Air Permeability Tester is designed to quickly and accurately measure the breathability and p... |
 |
Surface Performance Tester STD-FB4 - A | 卖方: Standard International Group (HK) Limited | Introduction TheSurface Tester analyzes finger movements-particularly, strokes-performed by arti... |
 |
Compression Tester STD - FB3 - A | 卖方: Standard International Group (HK) Limited | TheCompression Tester analyzes hand movements-particularly, pushing with a finger-performed by ar... |
 |
Single - Strand Bending Tester STD - FB2 - SH | 卖方: Standard International Group (HK) Limited | Standards ASTM A370. ASTM A416. ISO6934.4 The Single Fiber Bending Tester makes it possible to ... |
 |
Bending Tester STD- FB2 - S | 卖方: Standard International Group (HK) Limited | Compliance Standards ASTM D790 (Plastics Flexural Properties) ISO 178 (Flexural Strength of Rig... |
