Microbial Barrier Tester
Y/T 0471.5-2017 is a newly updated standard, which specifies the experimental method for evaluating the bacteria-inhibiting performance of the contact wound materials claimed to have bacteria-inhibiting performance. The bacteria-inhibiting test device can simultaneously meet the four test methods of wet bacteria-inhibiting, dry bacteria-inhibiting, semi-wet (dry outside and wet inside) bacteria-inhibiting, and semi-wet (wet outside and dry inside) bacteria-inhibiting.
Standard:
EN 15194:Cycles - Electrically power assisted cycles - EPAC Bicycles
ISO 4210:Cycles - Safety requirements for bicycles
UL 2849:Standard for Electric Bicycles and Electric Scoooters
ECE R50:Uniform provisions concerning the approval of front position lamps, rear position lamps, stop lamps, direction indicators and rear-registration-plate illuminating devices for vehicles of category L
Principle:
The sample was placed between two collets of a hemispherical glassware, a certain amount of standard bacterial solution was added to one side of the ware, and liquid medium was added to the other side, and the turbidity in the liquid medium was checked after a certain period of time
Or scrape the liquid to check for bacterial growth.
Advantages:
Ensures compliance with critical safety and performance standards for e-bike lighting.
Provides accurate and repeatable measurements of photometric and electrical parameters.
Allows for comprehensive evaluation of light distribution and beam patterns.
Facilitates durability testing under simulated environmental and mechanical stresses.
Supports efficient research and development of innovative and reliable lighting solutions.
Contributes to enhanced rider safety and visibility in various conditions.
Helps in meeting regulatory requirements for market access and product certification.
Features:
Goniophotometer: A precise instrument for measuring light intensity distribution in 3D space, essential for analyzing beam patterns and obtaining luminous intensity data.
Integrating Sphere: Used for measuring total luminous flux (lumens) and other integral photometric quantities, often with a spectroradiometer for color properties.
Photometers/Lux Meters: High-accuracy instruments for measuring illuminance at specific points or areas.
Programmable DC Power Supply: To provide stable and controllable power to the e-bike lighting device, simulating various battery conditions.
Electrical Measurement Unit: For measuring voltage, current, power consumption, and electrical efficiency of the lighting device.
Environmental Test Chambers: Chambers for simulating conditions such as extreme temperature, humidity, thermal shock, and salt spray.
Dust and Water Ingress Test Chambers: To evaluate the lighting device's IP (Ingress Protection) rating (e.g., IP6X, IPX7).
Vibration and Shock Test Systems: To assess the mechanical robustness and durability of the lighting device under typical e-bike operating conditions.
Control Software and Data Acquisition: Comprehensive software for automating test procedures, collecting data, analyzing results, and generating reports.
Fixture and Mounting: Adjustable fixtures to securely mount various types and sizes of e-bike lighting devices for testing.
Parameters
| Description | Details |
|---|---|
| Vibration type | Pneumatic ball vibrator |
| Vibration frequency | 20.800 times/min |
| Vibration force | 650N |
| Worktable dimensions | 40cm × 40cm × 10mm |
| Worktable material | Marble slab |
| Experimental container | Stainless steel experimental container |
| Number of working positions | 6 |
| Cabinet negative pressure range | -50 Pa to -200 Pa |
| High-efficiency filter filtration efficiency | Better than 99.99% |
| Negative pressure cabinet ventilation flow rate | ≥5m³/min |
| Data storage capacity | 100.000 sets |
| Operating voltage | 220V 50HZ |
Accessoriess
Two hemispherical glass devices,
two glass plugs,
two gooseneck glass tubes.
Test Procedures
Materials Preparation: Select suitable breathable packaging materials for testing.
Generation of Microbial Aerosols: Use an aerosol generator to produce microbial aerosols of a specific concentration.
Material Testing: Place the breathable packaging material to be tested into the testing apparatus, allowing the microbial aerosol to pass through the material.
Sampling: Use a six-channel filtration sampling device to simultaneously collect microbial samples from both the sample group and the control group.
Results Analysis: Evaluate the microbial barrier performance of the breathable packaging material by comparing the sampling results of the two groups.
在线联系供应商
Other supplier products
 |
Safety Helmet Lateral Rigidity Tester | Standard GB 2812: Safety Helmets (China National Standard) Equivalent Compliance: ISO 6220-2 (Industrial Safety Helmets – Lateral Deformati... |
 |
Leather edge oil fatigue testing machine | The Leather Edge Oil Fatigue Testing Machine is designed to evaluate the fatigue resistance of edge coatings applied on leather, synthetic leather,... |
 |
Rapid screening Calorimeter | The rapid - screening calorimeter is a professional calorimetric instrument for the quick assessment of reaction thermal hazards. It supports multi... |
 |
UV Condensation Aging Test Chamber丨UV Condensation Aging Tester | Standard ASTM G154.ISO 4892-3.JIS K 7350. andSAE J2020for UV exposure testing. IEC 60068-2-78for condensation and humidity resistance evaluations... |
 |
In-situ expansion analysis system | The In-situ Expansion Analysis System is designed for high-precision measurement of dimensional and volumetric changes in electrochemical cells and... |
Same products
 |
Gas Oxidizing Property Tester | 卖方: Standard International Group (HK) Limited | Product Description Conforms to ISO 10156-2010 “Gases and Gas Mixtures Selection of Cylind... |
 |
Battery Powder Compaction Density Measurement System | 卖方: Standard International Group (HK) Limited | The Battery Powder Compaction Density Measurement System is a precision testing system designed... |
 |
Battery Powder resistance tester | 卖方: Standard International Group (HK) Limited | The Powder Resistivity Meter is a precision testing system designed to measure electrical resisti... |
 |
KES-SESRU surface roughness/friction tester | 卖方: Standard International Group (HK) Limited | TheRoughness/Friction Tester analyzes hand movements-particularly, strokes-performed by artisans ... |
 |
Air Permeability Tester STD- F8 | 卖方: Standard International Group (HK) Limited | The Air Permeability Tester is designed to quickly and accurately measure the breathability and p... |
