Gas engine filter tester ISO 4548
Product Introduction:
The gas engine filter is an efficient filtration equipment used to filter and exclude impurities in the medium in the pipeline during the pipeline transportation process, and is a special device designed for the transmission of oxygen production pipe network, usually installed in the pressure reducing valve, pressure relief valve, fixed level valve or other equipment at the inlet end to eliminate impurities in the medium to protect the normal and safe use of valves and equipment.
The gas engine filter is composed of a shunt cone and a filter tube to purify the medium in the pipeline, improve the quality of natural gas, and prevent accidents caused by poor quality of natural gas. At present, it has been widely used in petroleum, chemical, pharmaceutical, food, environmental protection and other industries.
Standards:
ISO 4548. ISO 5011. SAE J905. GB/T 28949. GB/T 14295
Applications:
1. Weakly corrosive materials in petrochemical gas production: water, oil, ammonia, hydrocarbons, etc.
2. Corrosive materials in chemical production: caustic soda, soda ash, concentrated sulfuric acid, carbonic acid, acetic acid, ester acid, etc.
3. low temperature materials in industrial production: liquid methane, liquid ammonia, liquid oxygen and various refrigeration.
4. food, pharmaceutical production of hygiene requirements of the material: beer, beverages, dairy products, food pulp and medical supplies.
Operation and maintenance:
1. the first installation should be cleaned after a period of time to remove impurities and other dirt accumulated on the filter screen during the initial operation of the system.
2. the natural gas filter must be regularly checked and cleaned during use, and the frequency is determined according to the actual working conditions. When the filter works for a period of time, some impurities will precipitate inside the filter element, so that the pressure increases and the flow rate decreases, which needs to be removed in time.
3. when cleaning impurities, pay special attention to protect the stainless steel wire mesh layer covered by the surface of the filter element, can not be deformed or damaged; If the wire mesh layer is found to be deformed or damaged, it needs to be replaced immediately.
4. If the filter does not have a drain plug, the filter stopper and filter screen should be removed during cleaning.
5. Before each maintenance and cleaning, the filter should be isolated from the pressure system. After cleaning, use a new gasket when reinstalling.
Technical parameters
1. Test air volume: 3-30 m³/h, can be customized.
2. Test gases: HzS, SO2. NH3. C Hg, etc.
3. Test area: <20x20cm.
4.Pressure range: 0-500 Pa, 0~1000 Pa, 0-3000 Pa, you can choose one.
5. Test period: can be set freely, minimum >5s.
6. Gas analyzer: according to test gas, PlD, electrochemical, infrared, etc. For Toluene: measuring range
100ppm, accuracy+ 2% F'S, resolution 0.01ppm.
7. Accuracy of pressure gauge: 1%.
8. Dimensions (L*W*H):750x800x1750mm (Excluding gas cylinder and fan).
9. Power supply: AC220V, 50Hz,2000W.
在线联系供应商
Other supplier products
 |
Leather Seam Fatigue Tester |Seam Fatigue Tester | Textile Testing Products | Standards ISO 5402: Leather physical testing – Flex tester method for adhesion and strength analysis. SATRA TM55: Seam fatigue testing for ... |
 |
Catheter Burst Pressure Tester / Catheter Burst Pressure Testing Equipment | Compliance Standards YY/T 1536 - 2017 YY 0285.1 - 2017. etc. Main Uses The catheter burst pressure tester is a key device used to evaluate cathe... |
 |
Fabric Fiber Shedding Degree Tester (Friction Method) / Fabric Shedding Test Machine | Instrument Testing Principle Lay the specimen flat and fix it on the holder. Make the wet abrasive attached to the friction head perform reciproca... |
 |
Shoe Heel Impact Fatigue Tester / Shoe Heel Fatigue Tester | Meet the standard BS-5131 SATRA TM21. etc Main uses Heel impact fatigue testing machine is mainly used to test the continuous impact tolerance ... |
 |
Computer controlled electronic universal testing machine | Product Introduction 1. Meet the standard "GB/6344-2018 soft foam polymer tensile strength and elongation at break determination, GB/T6669-2008 fo... |
Same products
 |
Bottle Wall and Bottom Thickness Tester | 卖方: Standard Group (Hong Kong) Limited | The wall and bottom thickness tester for bottles is a measuring instrument widely used in the pha... |
 |
Pinhole Tester / Pinhole Testing Equipment | 卖方: Standard Group (Hong Kong) Limited | The pinhole tester for aluminum foil is a device specifically used to detect micro - pinholes in ... |
 |
Cork Puncture and Chip Detection Instrument | 卖方: Standard Group (Hong Kong) Limited | The rubber stopper puncture debris detector is a device specifically used to detect the number of... |
 |
Aluminum Ointment Tube Toughness Tester | 卖方: Standard Group (Hong Kong) Limited | The ductility tester for aluminum tubes is a device specifically used to detect the ductility ind... |
 |
Vacuum leak tester / Vacuum leak instrument | 卖方: Standard Group (Hong Kong) Limited | Vacuum Decay Leak Tester specializes in the detection of leaks in ampoules, vials, injection bott... |
