ISO 12103-2 M2 Test Dust

Product Introduction:

Particle Technology Fuel Contamination Test Dust offers a full range of fuel contamination test materials used to test the reliability of components of fuel and hydraulic oil systems in the aerospace and automotive industries. Typical mixtures of contaminants tested within the fuel system range from iron oxidation(rusting)to carbon fiber rods, graphite epoxy composites and fire extinguishing foams.

Standards:

ASTM E1226-22. IEC 60079-20-2:2022. ISO 6184-1:2023. EN 14034-4:2021. NFPA 68:2023.ISO 12103-2

Advantages:

Particle Technology UK has considerable experience in testing dust for fuel pollution to meet UK, EU, US, Japanese and international standards. The test dust can also meet Arizona dust, regardless of particle distribution and composition, to meet the specific requirements of the customer. Standard tests simulate dust from deserts to cities, from natural gas pipelines to jet fuel, and from railroads to airplanes. This allows you, as a customer, to test your product in real-life situations to highlight its advantages.

Parameters:

Maximum Explosion Pressure (Pmax): Pressure value (0-20 bar, refer to ASTM E1226)

Maximum Explosion Pressure Rise Rate (dP/dt)max): Rate value (0-1000 bar/s)

Explosion Index (Kst): Classification value (St0-St3) )

Concentration Limits:

Minimum Explosive Concentration (MEC): Concentration values (10-500 g/m³, refer to GB/T 16425)

Maximum Explosive Concentration (MOC): Concentration values (500-5000 g/m³)

Critical Dilution Concentration: Inert Addition Amount (≥ 50 vol%)

Particle Size Distribution:

Mean Particle Size (D50): Size Range (1-500 μm)

Distribution Width (Span): Value (≤ 2.0)

Fine Powder Content: Percentage (<75 μm, ≥ 20%)

Humidity Effect:

Critical Humidity Point: Relative Humidity (≥60%)

Moisture Content Impact: Moisture Content (≤5wt%)

Dry Dust Ignition Delay: Time Value (<10ms)

Oxygen Content Correlation:

Minimum Oxygen Concentration (MOC): Oxygen Content (≤12vol%)

Oxygen Limiting Index: Value (≥0.21)

Inerting Concentration: Inert Gas Proportion (≥30vol%)

Dust Layer Characteristics:

Layer Thickness Ignition Temperature: Temperature Threshold (≥300°C)

Bulk Density: Value (0.2-1.5g/cm³)

Autoignition Propensity: Time Delay (≤60min)

Dispersion Performance:

Dust Cloud Formation Efficiency: Dispersion Factor (≥0.8)

Suspension Time: Duration (≥5s)

Settling Rate: Velocity (0.1-10cm/s)

Electrostatic Parameters:

Dust Resistivity: Value (10^6-10^12Ω·cm)

Charge Decay Time: Time (≤10s)

Electrostatic Spark Energy: Energy Threshold (≤30mJ)

Chemical Composition:

Volatile Matter: Percentage (≥10wt%)

Ash Impact: Ash Content (≤20wt%)

Combustible Material Ratio: Value (≥70%)

Other supplier products

	Infusion Pump Flow Rate Tester GB 8368	Compliance Standards GB 8368 - 2018 Disposable Infusion Sets, etc. Main Uses The infusion set flow rate tester is an instrument specifically des...
	SUGA U48 Carbon Arc Aging Tester	Main purpose: The Si80 domestic carbon arc aging chamber is a comprehensive climate testing device mainly used to simulate the changes in materi...
	Medical Suture Line Diameter Tester YY 1116	The Medical Suture Thread Diameter Tester is a specialized testing equipment used for measuring the diameter or linear diameter of medical suture t...
	Shoe Shank Stiffness Tester SATRA TM256	Standard SATRA TM256: Flexural and torsional stiffness testing for athletic, safety, and casual footwear. SATRA TM194: Dynamic fatigue resistance...
	Fabric sensory quality evaluation tester	Product innovation: The "feel and look", or so-called "sensory perception", of fabrics and knitted fabrics, nonwovens, paper products, leather and...

供应产品

Same products

	Bottle Wall and Bottom Thickness Tester	卖方: Standard Group (Hong Kong) Limited	The wall and bottom thickness tester for bottles is a measuring instrument widely used in the pha...
	Pinhole Tester / Pinhole Testing Equipment	卖方: Standard Group (Hong Kong) Limited	The pinhole tester for aluminum foil is a device specifically used to detect micro - pinholes in ...
	Cork Puncture and Chip Detection Instrument	卖方: Standard Group (Hong Kong) Limited	The rubber stopper puncture debris detector is a device specifically used to detect the number of...
	Aluminum Ointment Tube Toughness Tester	卖方: Standard Group (Hong Kong) Limited	The ductility tester for aluminum tubes is a device specifically used to detect the ductility ind...
	Vacuum leak tester / Vacuum leak instrument	卖方: Standard Group (Hong Kong) Limited	Vacuum Decay Leak Tester specializes in the detection of leaks in ampoules, vials, injection bott...