Single chip liquid crystal touch impact testing machine
Product Introduction:
Liquid crystal touch impact testing machine is mainly used for hard plastics (including sheet, pipe, plastic profile)， reinforced nylon, glass fiber reinforced plastic, ceramic, cast stone, electrical insulation materials and other non-metallic materials impact toughness measurement, widely used in the chemical industry, scientific research units, universities and other quality testing departments.
Standards:
GB/T 18910.101-2021
IEC 60068-2-75:2014
Main features:
Not poor quality: the use of high hardness and high-precision bearings, and the use of shaftless photoelectric sensors, fundamentally eliminate the loss caused by friction, to ensure that the friction energy loss is far less than the standard requirements.
Intelligent prompt: According to the impact of the situation, intelligent prompt working status, always interact with the experimenter, to ensure the success rate of the test.
Friendly interface: there are parameter setting interface - result query interface - measurement interface - system setting interface, each operation has a clear user prompt, you can record 10 test records, you can choose domestic and international standards, you can choose Chinese and English.
Accurate measurement: In full accordance with the provisions of the new standard, after 10 swing cycles for a calculation of energy loss, each measurement to go through 3 times to average, to ensure the accuracy of energy loss.
Performance parameters:
1. Simple beam impact testing machine
- Impact speed: 2.9m/s
- Impact energy: 1/2/4/5J
- Maximum friction loss energy: <0.5%
- Pendulum prelift Angle: 150±1°
- Strike center distance: 230mm
- Power supply: 220VAC-15% —— 220VAC+10%, 50Hz(single-phase three-wire system)
2. Cantilever beam impact testing machine
- Impact speed: 3.5m/s
- Impact energy: 1J; 2.75 J; 5.5 J; 11J; 22J(3 hammers, customer's choice)
- Maximum friction loss energy: <0.5%
- Pendulum prelift Angle: 150±1°
- Strike center distance: 335mm
- Power supply: 220VAC-15% —— 220VAC+10%, 50Hz(single-phase three-wire system)
在线联系供应商
Other supplier products
 |
High Acceleration Shock Test System / Shock Test Machine | Applications: The size of the impact test bench is small, and the bench structure is carefully designed after finite element optimization analysis... |
 |
Film punching machine ASTM | Meet the standard: GB/T1528; GB/T529; GB/T8083; GB/T 15340.ASTM Technical parameters: Travel range :100mm Blanking force: about 20kN Table siz... |
 |
Shoe peeling strength tester BS 20344 | Product Introduction: Upper peeling strength tester is suitable for testing the peeling strength between the sole and the upper of the shoe, the p... |
 |
Friction and wear testing machine - Friction / Wear Mechanical Testing Equipment | Standards ASTM G99-04 ASTM G77-16 ISO 9352:1995 GB/T 12444-2006 GB/T 12607-2007 GB/T 1865-2009 Application field Petrochemical: Used to ass... |
 |
Suga GX25 | GX25 is designed to artificially reproduce indoor deterioration factors such as sunlight,temperature and humidity.GX25 exposes materials to these... |
Same products
 |
Bottle Wall and Bottom Thickness Tester | 卖方: Standard Group (Hong Kong) Limited | The wall and bottom thickness tester for bottles is a measuring instrument widely used in the pha... |
 |
Pinhole Tester / Pinhole Testing Equipment | 卖方: Standard Group (Hong Kong) Limited | The pinhole tester for aluminum foil is a device specifically used to detect micro - pinholes in ... |
 |
Cork Puncture and Chip Detection Instrument | 卖方: Standard Group (Hong Kong) Limited | The rubber stopper puncture debris detector is a device specifically used to detect the number of... |
 |
Aluminum Ointment Tube Toughness Tester | 卖方: Standard Group (Hong Kong) Limited | The ductility tester for aluminum tubes is a device specifically used to detect the ductility ind... |
 |
Vacuum leak tester / Vacuum leak instrument | 卖方: Standard Group (Hong Kong) Limited | Vacuum Decay Leak Tester specializes in the detection of leaks in ampoules, vials, injection bott... |
