Car seat belt fixed point test bench
Applicable standards:
National mandatory standards:
GB 15083-2006"Automobile seats, seat fixtures and headrests strength requirements and test methods"
GB 14167-2006/2013"Car Seat Belt installation Fixed Point"
GB 11550-2009"Automobile seat headrest strength requirements and test methods"
GB 13057-2003/2014"Strength of passenger seats and their vehicle fasteners"
GB 14166-2013"Seat belt, restraint system, Child restraint System for Motor Vehicle Occupants ISOFIX Child Restraint System"
International Standards and regulations:
Eu ECE R14Uniform Regulation on the approval of Vehicles with regard to seat belt fixing Points
Eu ECE R17Uniform Regulation on the approval of vehicles with regard to seats, seat fixation points and headrests
Eu ECE R80（specific terms may vary from version to version）
FMVSS 207Seating System
FMVSS 210Seat Belt Assembly Fixing Point
FMVSS 225Child Restraint System Fixed Point
Enterprise standard:
For example, the test requirements of the strength of the seat system and the strength of the seat belt fixing point in the EP development standard of the German Volkswagen company.
SAE J 384Stationary Point Test Code for Seat Belts in Motor Vehicles
SAE J 385, Motor Vehicle Seat Belt fixed point performance requirements, etc.
Main parameters:
| Parameter Category | Technical Specification Description |
|---|---|
| Load Measuring Range | - Multi-channel (e.g., 6 channels): 0–30 kN - Fewer channels (e.g., 3 channels): 0–15 kN |
| Control Accuracy | -0–30 kN Force Measurement Control System ▸ Control accuracy: ±200 N (for measured/controlled loads of 5–30 kN) ▸ Control accuracy: ±100 N (for measured/controlled loads of 0–5 kN) -0–15 kN Force Measurement Control System ▸ Control accuracy values are reduced proportionally (specific values not provided) |
| Hydraulic Cylinder Configuration | - Quantity: Varies by test bench design (e.g., 9 cylinders for a nine-channel bench) - Single-Cylinder Load Capacity: Must meet test requirements (e.g., 3-tonne rated load) |
| Stroke & Loading Speed | - Hydraulic Cylinder Stroke: Typically ≥1000 mm (to accommodate various seat/anchor point sizes) - Loading Speed: Achieves preset output within ≤2 seconds |
| Load Holding Time | - Adjustable Range: 0.2–120 seconds (stepless adjustment) |
在线联系供应商
Other supplier products
 |
Cigarette paper smoldering performance tester | Product Introduction: Cigarette paper smoldering performance tester, also known as smoldering instrument, cigarette paper burning performance test... |
 |
Automotive Wires Flammability Tester | Compliance Standards FMVSS 302 (Federal Motor Vehicle Safety Standard) ISO 6722 (Road Vehicle Cable Flammability) UL 94 (Tests for Flammability ... |
 |
Manual Crockmeter for Color Fastness Tester-QINSUN | Standard AATCC 8(Colorfastness to Crocking) ISO 105-X12(Textiles - Tests for Colour Fastness - Part X12: Colour Fastness to Rubbing) ASTM D505... |
 |
Water injection counterweight dummy | Product Introduction This counterweight dummy can be filled with water, the torso and the bottom are separated, independently filled with water o... |
 |
Air Permeability Tester-QINSUN | Air Permeability Tester of textile fabrics complies with ASTM D737. ISO 9237/7231. BS 5636. etc. It is used to test the resistance of the flow of a... |
Same products
 |
Seat Bumping and Creep Test Bench | 卖方: Standard International Group (HK) Limited | This test bench is used for simulating the car seat bumping and creep situation when a car is run... |
 |
Automobile seat belt fixed point test bench | 卖方: Standard International Group (HK) Limited | Applicable standards: National mandatory standards: GB 15083-2006"Automobile seats, seat fixtur... |
 |
Impact strength tester for car seat headrest | 卖方: Standard International Group (HK) Limited | Applicable standards: GB 15083-2006 "Automobile seats, seat fixtures and headrest strength requi... |
 |
Impact strength tester for car seat launching headrest | 卖方: Standard International Group (HK) Limited | Main parameters: Impact speed:The impact speed of the tester is usually between 25 and 30km/h, w... |
 |
Automobile Headrest Strength Tester | 卖方: Standard International Group (HK) Limited | Applicable standards: GB 11550-2009"Automobile seat headrest strength requirements and test me... |
