Car seat belt fixed point test bench
Applicable standards:
National mandatory standards:
GB 15083-2006"Automobile seats, seat fixtures and headrests strength requirements and test methods"
GB 14167-2006/2013"Car Seat Belt installation Fixed Point"
GB 11550-2009"Automobile seat headrest strength requirements and test methods"
GB 13057-2003/2014"Strength of passenger seats and their vehicle fasteners"
GB 14166-2013"Seat belt, restraint system, Child restraint System for Motor Vehicle Occupants ISOFIX Child Restraint System"
International Standards and regulations:
Eu ECE R14Uniform Regulation on the approval of Vehicles with regard to seat belt fixing Points
Eu ECE R17Uniform Regulation on the approval of vehicles with regard to seats, seat fixation points and headrests
Eu ECE R80（specific terms may vary from version to version）
FMVSS 207Seating System
FMVSS 210Seat Belt Assembly Fixing Point
FMVSS 225Child Restraint System Fixed Point
Enterprise standard:
For example, the test requirements of the strength of the seat system and the strength of the seat belt fixing point in the EP development standard of the German Volkswagen company.
SAE J 384Stationary Point Test Code for Seat Belts in Motor Vehicles
SAE J 385, Motor Vehicle Seat Belt fixed point performance requirements, etc.
Main parameters:
| Parameter Category | Technical Specification Description |
|---|---|
| Load Measuring Range | - Multi-channel (e.g., 6 channels): 0–30 kN - Fewer channels (e.g., 3 channels): 0–15 kN |
| Control Accuracy | -0–30 kN Force Measurement Control System ▸ Control accuracy: ±200 N (for measured/controlled loads of 5–30 kN) ▸ Control accuracy: ±100 N (for measured/controlled loads of 0–5 kN) -0–15 kN Force Measurement Control System ▸ Control accuracy values are reduced proportionally (specific values not provided) |
| Hydraulic Cylinder Configuration | - Quantity: Varies by test bench design (e.g., 9 cylinders for a nine-channel bench) - Single-Cylinder Load Capacity: Must meet test requirements (e.g., 3-tonne rated load) |
| Stroke & Loading Speed | - Hydraulic Cylinder Stroke: Typically ≥1000 mm (to accommodate various seat/anchor point sizes) - Loading Speed: Achieves preset output within ≤2 seconds |
| Load Holding Time | - Adjustable Range: 0.2–120 seconds (stepless adjustment) |
Отправить запрос, связаться с поставщиком
Другие товары поставщика
 |
Footwear Dynamic Waterproof Tester | Product Introduction: It is used to test the dynamic waterproof performance of various finished shoes, and the number of times when no water enter... |
 |
Car seat static strength tester | Applicable standards: GB 11550-2009"Car seat headrest strength requirements and test methods" : This standard specifies the static strength test r... |
 |
MMT Liquid Water Separation Tester-QINSUN | |
 |
Car seat center of gravity measuring tester-QINSUN | Main parameters: Measuring range:refers to the maximum and minimum range of the center of gravity of the seat that the tester can measure. This ... |
 |
Toilet Paper Dispersibility Tester | Product Introduction: G354B toilet paper dispersibility tester is a test instrument used to test the dispersibility of toilet paper, dispersibilit... |
Похожие товары
 |
Seat Bumping and Creep Test Bench | Продавец: Standard International Group (HK) Limited | This test bench is used for simulating the car seat bumping and creep situation when a car is run... |
 |
Automobile seat belt fixed point test bench | Продавец: Standard International Group (HK) Limited | Applicable standards: National mandatory standards: GB 15083-2006"Automobile seats, seat fixtur... |
 |
Impact strength tester for car seat headrest | Продавец: Standard International Group (HK) Limited | Applicable standards: GB 15083-2006 "Automobile seats, seat fixtures and headrest strength requi... |
 |
Impact strength tester for car seat launching headrest | Продавец: Standard International Group (HK) Limited | Main parameters: Impact speed:The impact speed of the tester is usually between 25 and 30km/h, w... |
 |
Automobile Headrest Strength Tester | Продавец: Standard International Group (HK) Limited | Applicable standards: GB 11550-2009"Automobile seat headrest strength requirements and test me... |
