Low-Temperature Bending Resistance Tester
Applicable Standards
The tester adheres to international standards for material testing at low temperatures, including:
ISO 4674-2(Rubber- or plastics-coated fabrics – Determination of low-temperature bend test)
ASTM D1790(Standard test method for resistance of organic coatings to the effects of rapid deformation (impact))
GB/T 2423(China’s national standard for environmental testing – Cold tests)
EN 60068-2-1(Environmental testing – Cold tests for electronic components)
SAE J2339(Cold temperature impact resistance for automotive coatings)
These standards ensure consistent evaluation of material behavior under thermal and mechanical stress.
Working Principle
The tester operates bycombined thermal and mechanical stress:
Temperature Conditioning: Samples are cooled to -70°C in a climate chamber.
Bending Cycle: A motorized arm repeatedly bends the sample at a preset angle (e.g., 90° or 180°) and frequency (e.g., 100 cycles/min).
Cycle Execution: The test runs until surface cracks appear, or a predefined cycle count (e.g., 20.000 cycles) is reached.
Damage Assessment: Post-test, samples are evaluated for cracking, delamination, or coating failure using microscopy or visual grading.
Test Principle & Applications
Cold Flexibility Testing (ISO 4674-2/ASTM D1790):
Samples are bent 10.000–50.000 times at -40°C to simulate polar or alpine conditions.
Results are graded based on crack appearance:
Pass: No visible cracks or coating separation.
Fail: Cracks exceeding 0.5 mm in width.
Key Industries:
Aerospace: Validating aircraft fuel lines and sealants.
Automotive: Testing battery packs and exterior trim for electric vehicles.
Construction: Assessing pipe insulation and roofing membranes.
The Low-Temperature Bending Resistance Tester is indispensable for manufacturers developing products for extreme climates, ensuring reliability and compliance with regulatory standards. Its precision and adaptability make it a cornerstone of materials testing in harsh environments.
Main Parameters
| Parameter | Specification |
|---|---|
| Temperature Range | -70°C to +200°C (adjustable via cryogenic cooling) |
| Bending Angle | 0–180° (adjustable for different material flex requirements) |
| Stroke Frequency | 50–300 cycles/min (programmable) |
| Sample Dimensions | 100 × 20 mm (standard for coatings/films); up to 300 × 50 mm (customizable) |
| Cooling System | Liquid nitrogen or mechanical refrigeration (LC-120 model) |
| Control System | PLC-based with 7-inch touchscreen (multilingual interface) |
| Power Supply | 220V/50Hz, 800W |
| Dimensions | 800 × 600 × 1500 mm (L × W × H) |
在线联系供应商
Other supplier products
 |
AATCC KMS-M6 Washer, KMS-M6D Dryer-QINSUN | Product Overview TheAATCC KMS-M6 Washer & KMS-M6D Dryerare precision textile testing instruments designed to evaluate fabric durability, col... |
 |
Automatic 55 Gallon Drum washer, 200L Barrel Cleaning Solution | Features: This semi-automatic200 liters barrel cleaning systemutilizes our rotary impingement technology and is designed to blast stubborn residue... |
 |
Locomotive wire dynamic cutting through tester | Applicable standards: Test requirements inEN50305EN50306:2002 Main functions: 1. Fix the sample on the steel platform, place the indenter with... |
 |
Hexapod Tumbler test machine | Standard BSEN 1471:1997: Evaluation of Appearance Changes in Floor Coverings ISO 9405:2001: Floor Coverings – Determination of Appearance C... |
 |
Thermal Protective Performance Tester (TPP) | The Thermal Protective Performance (TPP) Test Device was developed to measure the time elapsed for convective and radiant heat to penetrate through... |
Same products
 |
Seat Bumping and Creep Test Bench | 卖方: Standard International Group (HK) Limited | This test bench is used for simulating the car seat bumping and creep situation when a car is run... |
 |
Automobile seat belt fixed point test bench | 卖方: Standard International Group (HK) Limited | Applicable standards: National mandatory standards: GB 15083-2006"Automobile seats, seat fixtur... |
 |
Impact strength tester for car seat headrest | 卖方: Standard International Group (HK) Limited | Applicable standards: GB 15083-2006 "Automobile seats, seat fixtures and headrest strength requi... |
 |
Impact strength tester for car seat launching headrest | 卖方: Standard International Group (HK) Limited | Main parameters: Impact speed:The impact speed of the tester is usually between 25 and 30km/h, w... |
 |
Automobile Headrest Strength Tester | 卖方: Standard International Group (HK) Limited | Applicable standards: GB 11550-2009"Automobile seat headrest strength requirements and test me... |
