Thermal Protective Performance Tester (TPP)

The Thermal Protective Performance (TPP) Test Device was developed to measure the time elapsed for convective and radiant heat to penetrate through a protective composite fabric system - measuring the resulting damage to human skin.

Standards：

BS EN ISO 6942. EN 366. EN 407. ISO 11612. ASTM F1939. ASTM F2702. NFPA 1971. NFPA 2112. GB 38543. GB/T 38306

Feature：

Industrial personal computer with analysis software is suitable for severe testing conditions.

Automatic calculation for heat transmission factor and radiant heat transfer index.

Sample holder with force applied kit is easy to operate.

Single pump for shutter movement and cooling water loop.

Parameter：

• Up to 7.5 in x 7.5 in. (19 cm x19 cm) sample size

• Copper slug calorimeter sensors (ASTM or ISO)

• ± 0.75°C temperature measurement

• ± 3% radiant heat flux measurement

• Device Dimensions: 42 in. x 20 in. x 18 in. (107 cm x 51 cm x 46 cm)

• Space Requirements: 46 in. x 26 in. x 24 in. (117 cm x 67 cm x 61cm)

• Power Requirements: 208-265 VAC, 50/60Hz, Single-phase

• Maximum nominal current 20 Amps

• Compressed Air: Clean/dry air at 70-90 PSI, (145 PSI max)

• Cooling Water: Cooling water required, chiller or tap water source is acceptable

• Propane Requirement: Regulated supply at 15 PSI (minimum)

• Water-cooled radiant heat source with 9 quartz (500W) infrared lamps

• Two gas burners with flame detection auto ignition

• Mass flow controller for precise gas control

• Water-cooled protective shutter

• Pneumatic sample carriage and shutter assembly

• Integrated sensor cooling stand (air cooled)

• Emergency stop cuts gas flow, power to lamps and pneumatics

• Tinted tempered glass shield protects operator

• Software safety interlocks monitor water flow, carriage position, burner ignition

Other supplier products

	Sand and Dust Test Chamber	The sand and dust test chamber for automotive connectors meets the requirements of protection - class tests for the enclosures of household appli...
	Car seat component clearance test bench Degree of automation:	Applicable standards: Car seat component clearance test benches usually follow the following domestic and international standards: QC/T 805-2008"...
	Schopper Abrasion Tester	Standards DIN 53863, Part 2: Abrasion test methods for textile fabrics (rotary abrasion test). GME Standard 60345 & GMW Standard 3283: Indu...
	Automotive Wires Low - temperature Impact Tester	Standard: ISO 6722-1. ISO 14572: International benchmarks for electrical cable performance in low-temperature environments. ISO 19642: Road veh...
	Paper whiteness tester	Introduction: Paper whiteness tester is suitable for the whiteness measurement of non-color surface flat objects or powders, and can accurately me...

供应产品

Same products

	Blanket Flammability Test Machine	卖方: Standard Groups	Bed Blanket Flammability Tester-It is mainly used for testing the flame retardant performance of ...
	High Temperature Oxygen Index Tester	卖方: Standard Groups	The High-Temperature Oxygen Index (TOI) measuring instrument determines oxygen index at up to 125...
	Limiting Oxygen Index Tester	卖方: Standard Groups	The Limiting Oxygen Index Tester measures the minimum oxygen concentration needed to sustain comb...
	Vertical Flammability Tester	卖方: Standard Groups	Vertical Flammability Chamber for measuring the vertical flame spread for children’ sleepwe...
	45 Degree Flammability Tester	卖方: Standard Groups	Application 45 Degree Flammability Tester is used to determine the burning characteristics of te...