RS232/485 Digital Signal to 4-20ma Analog Signal Converter
RS485/232 to 4-20ma/0-5V/0-10V/0-2.5V D-A Converter
Model Selection:
ISODA O□- □
Output voltage or current value Communication Interface
O1:4-20mA 485： out is RS-485 interface
O2:0-20mA 232： out is RS-232 interface
O4:0-5V 232/485：out is one RS232 or RS485 interface
O5:0-10V (Key-press Choice)
O6:1-5V
O7:0-±5V
O8:user-defined
O9: 0-±20mA
O10: 0±10V
Note:When interface type is 232/485, default is RS485 output, user can switch between RS485 and RS232 by pushing down 2 buttons inside the chassis. When both buttons are pushed down, output is RS232,or is RS485 output.
Example:
1. ISODA O1-485 Means 4-20ma signal output,output is RS485 interface
2. ISODA O4-232 Means 0-5V signal output,output is RS232 interface.
3. ISODA O7-232/485 Means 0-±5V signal output,output is RS485 or RS232 interface
(Key-press Choice)
General Parameters
(typical @ +25℃,Vs is 24VDC)
Outputs: Voltage / Current
Accuracy: 0.2%
Output Maladjustment: current output ±0.5 uA/℃,voltage output ±0.1mV/C
Temperature Drift: ±20 ppm/℃(±30 ppm/℃,max)
Output Resistance: current output 350Ω (4-20mA/0-20mA/0-±20mA output)
Voltage output 10mA (0-5V/0-10V/0-±5V output)
Communications
Protocol RS-485 or RS232 ASCII format,MODBUS
Baud Rates Software Selectable (300、600、1200、2400、4800、9600、19200、38400bps）
Address (0～255) Software Selectable
Response Time: 100 ms,max
Operation Power Supply: +8~50VDC
Power Loss: <1.5W
Operation Temperature: - 45 ~ +80℃
Operation Humidity: 10 ~ 95% (non-condensing)
Storage Temperature: - 45 ~ +80℃
Storage Humidity: 10 ~ 95% (non-condensing)
Isolation Input/Output: 3KVDC,1 minute,leak current:1mA
Interface and power supply are common-ground.
Endure Impact Voltage: 3KVAC,1.2/50us(peak value)
Mechanical Dimensions: 83 mm x 37 mm x 51 mm
Send product request
Other supplier products
 |
J/K/T/E/R/S/B Type Thermocouple Signal to RS232 or RS485 Converter SYAD-08T Series- | Product Description 8-Channels Thermocouple Signal to RS232/RS485 A-D Converter SY AD08T Series Thermalcouples Signal A-D Converter Model Selection... |
 |
Customized Non-isolation 4-20mA Two-wire Analog Isolated transmitter | 4-20mA Signal Conditioner Features >>Power supply no needed, non-isolation, two-wire loop powered. >>Wide range input voltage signal &g... |
 |
SY LED1 Current Signal Digital Panel Meter | .Low cost module design ,easy to connected with converter and instrument &meters by PIM. .two wire passive working way, Need no other auxiliary... |
 |
4-digit LED display Current Loop Isolated Control Display Meter | .-Industrial site 4-20mA signal isolation monitoring and long distance transmission. .-Anti-interference & isolation among signal input channel... |
 |
DC Current/Voltage to RS485/232 A-D Converter Support Modbus RTU SYAD | Analog data acquisition isolated AD conversion amplifier module. Shunyuan technology patented products Product Description 2-Channel/4-channel DC C... |
Same products
 |
Rated Power 2400W 24VDC Solar Inverter | Seller: Shenzhen BaoEr Energy Technology Co., LTD. | Rated Power 2400W 24VDC Solar Inverter The DC 2.4 kw inverterwith a rated power of 2400 watts is... |
 |
Rated Power 2400W 24VDC PV Inverter | Seller: Shenzhen BaoEr Energy Technology Co., LTD. | Rated Power 2400W 24VDC PV Inverter This is a single phase inverter rated at 2400 watts, 24 volt... |
 |
Rated Power 2400W 24VDC Pure Sine Wave Solar Inverter | Seller: Shenzhen BaoEr Energy Technology Co., LTD. | Rated Power 2400W 24 Volt Pure Sine Wave Inverter It is a new generation of power inverter with ... |
 |
Rated Power 2400W 24VDC Off Grid Solar Inverter | Seller: Shenzhen BaoEr Energy Technology Co., LTD. | Rated Power 2400W 24VDC Off Grid Solar Inverter This is a cost-effective solar inverter that acc... |
 |
Rated Power 2400W 24VDC Battery Inverter | Seller: Shenzhen BaoEr Energy Technology Co., LTD. | Rated Power 2400W 24VDC Battery Inverter The Rated Power 2400W 24VDC Battery Inverter is a mid-r... |
