Helmet Surface Friction Tester
Get a quote：
Whats/App: +86 181 0160 0864
Web: gellowen.co.uk
The Helmet Surface Friction Tester is a device used to evaluate the frictional properties of helmet surfaces. It measures how the helmet outer material interacts with different surfaces or materials, helping to assess slip resistance, abrasion, and overall surface durability under controlled conditions.
Application
The Helmet Surface Friction Tester evaluates the friction resistance of helmets. The helmet is pressed onto a movable fixture with a specified force. The fixture surface is covered with sandpaper of a standard-defined grit. The test helmet is then moved across the sandpaper at a controlled speed, allowing assessment of the helmet’s frictional performance.
Standards
Meets the requirements of ECE R22.05.
Technical Specifications
(1)The tester can perform friction tests on both protruding areas and flat surfaces of the helmet.
(2)Impact weight: 15 kg
(3)Free-fall height: 500 mm
(4)Load cell force: 400 N (40.8 kg)
(5)Release mechanism controlled by an electromagnet
(6)Sandpaper or shear blocks can be installed on the horizontal guide frame to perform linear friction with the helmet surface.
(7)Adjustable helmet mounting fixture
(8)Touchscreen control
Accessories
(1)Test Pads and Sliders: Standardized materials for simulating hand or surface contact.
(2)Helmet Holders/Fixtures: Secure helmets in a repeatable position for consistent testing.
(3)Force Sensors: Measure frictional forces accurately during testing.
(4)Data Acquisition System: Collects real-time friction data for analysis.
Test Procedures
Sample Preparation: Clean helmets and mount securely in the fixture.
Parameter Setup: Set normal load, sliding speed, and contact angle according to test requirements.
Friction Measurement: Move test pad or slider across the helmet surface while recording friction force.
Data Analysis: Evaluate surface friction coefficient, wear, or abrasion patterns.
Send product request
Other supplier products
 |
Catheter Hydraulic Leakage Tester | Get a quote： Whats/App: +86 181 0160 0864 Web: gellowen.co.uk The Catheter Hydraulic Leakage Tester is a testing instrument specifically develop... |
 |
Footwear Dynamic Waterproof Tester | Get a quote： Whats/App: +86 181 0160 0864 Web: gellowen.co.uk The Footwear Dynamic Waterproof Tester is designed to evaluate the waterproof perf... |
 |
Battery Powder Compaction Density Measurement System | Get a quote： Whats/App: +86 181 0160 0864 Web: gellowen.co.uk The Battery Powder Compaction Density Measurement System is a precision testing sy... |
 |
Hot Tack Tester / Heat Seal Tester | Get a quote： Whats/App: +86 181 0160 0864 Web: gellowen.co.uk The Hot Tack Tester/Heat Seal Tester is specifically designed for testing the heat... |
 |
16-Segment Heated Thermal Manikin (Dry Type) | Get a quote： Whats/App: +86 181 0160 0864 Web: gellowen.co.uk The 16-Segment Heated Thermal Manikin (Dry Type) is a precision anthropomorphic me... |
Same products
 |
MMA-120 Handheld Arc Welder | Seller: 871183 | The MMA-120 Handheld Arc Welder from ChuangLi Electronic Technology Co., Ltd. is designed for con... |
 |
SHX Series Circulating Fluidized Bed Steam Boiler | Seller: Hebei Genjux Boiler Co.,Ltd | Capacity: 10-35 t/hWorking pressure: 1.25-2.5 MPaOperating temperature: 194-400 ℃Applicable to bi... |
 |
YQ(Y)W Series Oil/Gas Fired Vertical Thermal Oil Boiler | Seller: Hebei Genjux Boiler Co.,Ltd | Capacity: 7000-29200 KWOperating pressure: 0.8-1.0 MPaOperating temperature: 320℃Operating mode: ... |
 |
DHL Series Coal-Fired Steam Boilers | Seller: Hebei Genjux Boiler Co.,Ltd | Capacity: 35-75 t/hOperating pressure: 1.25-5.4 MPaOperating temperature: 194-485℃Applicable to b... |
 |
SZL Series Biomass Steam Boiler | Seller: Hebei Genjux Boiler Co.,Ltd | Capacity: 6-35 t/hWorking pressure: 1.0-2.5 MPaOperating temperature: 184-350 ℃Applicable fuel bi... |
