NES 713 Smoke Toxicity Tester, Toxic Gas Analyzer, Marine Fire Testing Equipment Manufacturer

Get a quote：

Whats/App: +86 156 1874 6768

Web: standard-groups.com

E-mail：info@standard-groups。com

Parameters

Parameter	Specification
Flame height	100–125 mm (blue flame)
Maximum hot spot temperature	1150 ± 25 °C
Number of sampling ports	12
Exhaust capacity	≥ 50 L/s
Gas supply	Compressed air, methane or natural gas
Power supply	AC 220 V, 50/60 Hz, 5 A
Equipment weight	Approx. 150 kg
Overall dimensions	1.185 (W) × 700 (D) × 2.100 (H) mm

Features

Rigid steel chamber with reinforced frame construction to ensure long-term structural stability

Large observation window with dark-coated inner walls to clearly observe the combustion behavior of specimens

Inner chamber walls treated with PTFE coating to reduce chemical corrosion caused by combustion gases

Built-in stirring fan to ensure uniform distribution of smoke and combustion gases inside the chamber

Top-mounted exhaust fan with stainless steel exhaust duct, automatically activated after test completion to discharge residual smoke

Integrated industrial design with panel-mounted structure, providing intuitive operation and ergonomic human–machine interface

High-voltage pulse automatic ignition system offering stable ignition performance and enhanced operational safety

Imported K-type thermocouples for accurate and reliable temperature measurement

Adjustable stainless steel specimen mesh tray allowing precise positioning relative to the flame

Imported precision rotameters for accurate control of gas and air flow rates

Branded pressure gauges, pressure regulators, and solenoid valves to control gas pressure and on/off status, ensuring safe operation

PLC and touchscreen control system enabling automatic control, detection, calculation, and data storage

Automatic waste exhaust mode to remove smoke upon test completion according to preset program logic

Manual and automatic test modes selectable to suit different testing requirements

Test Procedures

1. Pre-Test Preparation

Environment confirmation:

The test area should be an independent, well-ventilated space, kept away from flammable materials and densely populated areas. The floor must be dry and free of standing water. The power supply should be properly grounded and meet AC 220 V, 50/60 Hz, 5 A requirements.

Equipment inspection:

Check all gas pipelines (methane or natural gas) for leakage and confirm the gas cylinder pressure is within 0.2–0.3 MPa. Verify that the exhaust fan and stainless steel exhaust duct are unobstructed and capable of providing an exhaust capacity of at least 50 L/s. Confirm normal operation of the K-type thermocouples, rotameters, and PLC touchscreen with no alarm indications. Ensure proper door sealing, intact polycarbonate observation window, and undamaged PTFE inner wall coating.

Safety protection:

Operators should wear high-temperature resistant gloves, safety goggles, gas masks equipped for CO and HCN protection, and safety shoes. A portable multi-gas detector (monitoring O₂, CO, HCN, NOₓ) and an emergency eyewash station should be available on site.

2. Specimen Installation

Specimens should conform to NES 713 requirements, typically measuring 100 mm × 100 mm with a thickness not exceeding 10 mm. Cable materials may be fixed using a coiled arrangement. No more than three specimens should be tested in a single run, evenly distributed on the stainless steel mesh tray to avoid flame obstruction. Adjust the tray position so that it is located directly above the burner, with a distance of 100–125 mm from the burner nozzle to ensure full flame coverage on the specimen underside.

3. Ignition and Test Execution

Close the chamber door and confirm the locking mechanism is engaged. Select “Automatic Mode” on the control screen and start the test. The system will automatically perform high-voltage pulse ignition for approximately three seconds, followed by flame stability detection. If a stable flame is not detected within five seconds, re-ignition will be attempted automatically, up to three times. The combustion process typically lasts 10–15 minutes, during which the internal fan continuously mixes smoke to maintain uniform concentration.

4. Gas Sampling

Gas sampling begins at the fifth minute after ignition and continues until the end of combustion. Twelve dedicated sampling ports are used to connect gas detector tubes (for gases such as HCN, CO, and HCl) or online gas analyzers. Each sampling port is equipped with an independent flow meter, with the sampling flow rate controlled at no more than 1 L/min to avoid negative pressure interference. After sampling, tubes are sealed immediately, labeled with time and port number, and sent for quantitative laboratory analysis.

Other supplier products

	Helmet Molten Metal Splash Testing Device	Get a quote： Whats/App: +86 156 1874 6768 Web: standard-groups.com The Molten Metal Splash Resistance Tester is designed to evaluate the resista...
	ASTM Reciprocating Tribometer Manufacturer	Get a quote： Whats/App: +86 156 1874 6768 Web: standard-groups.com The Reciprocating Tribometer is a value-engineered tribological testing instr...
	Cloth Material Comfort Evaluation Device	Whats/App: +86 156 1874 6768 Web: standard-groups.com Application The instrument is widely used in: Textile R&D: Quantifying fabric hand fe...
	High and Low Temperature Material Impact Resistance Tester	Get a quote： Whats/App: +86 156 1874 6768 Web: standard-groups.com High-Low Temperature Multifunctional Aggregate Impact Tester is a professiona...
	Laboratory Cornell Mattress Fatigue Testing Machine Complying with ASTM F1566	Get a quote： Whats/App: +86 156 1874 6768 Web: standard-groups.com Features Large test platform suitable for King and California King mattresse...

All supplier products

Same products

	ER4047 Aluminum Mig Welding Wire	Seller: 868776	Hangzhou Kunli Welding Materials Co., Ltd. specializes in manufacturing reliable welding material...
	ER4043 Silicon Aluminum Welding Wire	Seller: 868776	Hangzhou Kunli Welding Materials Co., Ltd. specializes in manufacturing high-quality welding mate...
	Choosing the Right Equipment for Heavy-Duty Cleaning	Seller: Taizhou Feike Mechanical Technology Co., Ltd.	FEIKE’s High Pressure Washer is designed for industrial cleaning, equipment maintenance, ve...
	ER4043 Silicon Aluminum Welding Wire	Seller: 868776	Hangzhou Kunli Welding Materials Co., Ltd. offers ER4043 Silicon Aluminum Welding Wire for alumin...
	HDPE High Speed Water Cooled Double Wall Corrugated Pipe Extrusion Line	Seller: Shandong HUASU Plastic Technology Co.,Ltd.	The molds adopt the double flow channel structure and nitriding polishing processed die head. Thi...