Dental material color stability tester

The Dentistry Base Polymer Search Stability tester is an instrument used to evaluate the

color stability of dental base polymers under different environmental conditions. A base polymer

is a material used for dental restoration and correction, such as dentures, braces, dentures, etc.

Due to long-term use and the influence of the external environment, these base polymers may

undergo color changes, affecting their beauty and durability. The color stability tester evaluates

the color change of the base polymer under these conditions by simulating different environmental

conditions, such as light, temperature, humidity, etc. Testers usually use standardized test methods

and parameters to ensure the accuracy and comparability of test results.

　　During the test, a sample of the base polymer is placed in a tester and exposed to

predetermined environmental conditions. The tester records the initial color of the sample

and re-measures the color of the sample after a certain interval. The color stability of the base

polymer can be assessed by comparing the initial color with the color of subsequent measurements.

The use of this tester can help dentists and technicians to select polymer materials with better

color stability, thereby improving the effectiveness and durability of repairs and corrections. At the

same time, manufacturers can use this tester to evaluate and improve the color stability performance

of their products.

Enforce standards

　　YY0270.1-2011 and YY/T0631-2008.

Technical parameter

　　Control system :PLC;

　　Operation interface: color touch screen, Chinese and English switch;

　　Light source: illuminance is 150 0001X----- accuracy is not biased to 10%;

　　Color temperature range :5000K-10000K;

　　Filter: transmittance greater than 90%;

　　Test box: Water temperature 0-99 degrees, test temperature 37 degrees,

water temperature can be adjusted with temperature display;

　　Clip :304 stainless steel clip outer diameter 50MM, thickness 0.5MM;

　　Polyurethane film: thickness of 50UM-- 0.5MM;

　　The device comes with a dial indicator :0-25.5MM, fine 0.01MM;

　　Standard :15L constant temperature tank, temperature 0-99 degrees.

Other supplier products

	Voltage Drop Tester for Automotive Wire Connectors	The voltage drop tester for automotive wire connectors is suitable for measuring the voltage drop at similar connection interfaces such as the pins...
	Fabric thickness tester	Fabric thickness tester mainly used to measure the thickness of the fabric, suitable for leather, rubber and textiles and other materials, the thic...
	Paper folding tester	Compliance Standards: ISO 2758、ISO 2759 ASTM D774、 D774M TAPPI T 403、TAPPI T 804 Test principle： The machine uses the motor drive screw to m...
	Textile Spray Rating Tester	spray water repellency testerSpray Rating Tester /Fabric surface waterproof performance tester is designed to determine the surface wetting resista...
	Rubber non-rotor vulcanization Tester	Product Introduction: Non-rotor vulcanizer is a rubber processing industry control rubber material quality, rapid inspection and rubber basic rese...

All supplier products

Same products

	Air Permeability Tester STD- F8	Seller: Standard International Group (HK) Limited	The Air Permeability Tester is designed to quickly and accurately measure the breathability and p...
	Surface Performance Tester STD-FB4 - A	Seller: Standard International Group (HK) Limited	Introduction TheSurface Tester analyzes finger movements-particularly, strokes-performed by arti...
	Compression Tester STD - FB3 - A	Seller: Standard International Group (HK) Limited	TheCompression Tester analyzes hand movements-particularly, pushing with a finger-performed by ar...
	Single - Strand Bending Tester STD - FB2 - SH	Seller: Standard International Group (HK) Limited	Standards ASTM A370. ASTM A416. ISO6934.4 The Single Fiber Bending Tester makes it possible to ...
	Bending Tester STD- FB2 - S	Seller: Standard International Group (HK) Limited	Compliance Standards ASTM D790 (Plastics Flexural Properties) ISO 178 (Flexural Strength of Rig...